Regulation No 72 of the Economic Commission for Europe of the United Nations ... (42014X0314(01))
INHALT
Regulation No 72 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of motor cycle headlamps emitting an asymmetrical passing beam and a driving beam and equipped with halogen lamps (HS 1 lamps)
- Regulation No 72 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of motor cycle headlamps emitting an asymmetrical passing beam and a driving beam and equipped with halogen lamps (HS
- 1
- lamps)
- 1. SCOPE
- 2. DEFINITIONS
- 3. APPLICATION FOR APPROVAL
- 4. MARKINGS(2)
- 5. APPROVAL
- 6. GENERAL SPECIFICATIONS
- 7. REQUIREMENTS FOR ILLUMINATION
- 7.1. General provisions
- 7.2. Provisions concerning passing beams
- 7.3. Provisions concerning driving beams
- 8. PROVISIONS CONCERNING COLOURED LENSES AND FILTERS
- 9. STANDARD (REFERENCE) HEADLAMP(12)
- 10. OBSERVATION CONCERNING COLOUR
- 11. CONFORMITY OF PRODUCTION
- 12. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 13. MODIFICATION OF HEADLAMP TYPE AND EXTENSION OF APPROVAL
- 14. PRODUCTION DEFINITELY DISCONTINUED
- 15. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
- 16. TRANSITIONAL PROVISIONS
- ANNEX 1
- COMMUNICATION
- (maximum format: A4 (210 × 297 mm))
- ANNEX 2
- VERIFICATION OF CONFORMITY OF PRODUCTION OF HEADLAMPS
- EQUIPPED WITH HS
- 1
- LAMPS
- ANNEX 3
- ARRANGEMENTS OF APPROVAL MARKS
- (see paragraph 5 of this Regulation)
- ANNEX 4
- MEASURING SCREEN
- ANNEX 5
- TESTS FOR STABILITY OF PHOTOMETRIC PERFORMANCE OF HEADLAMPS IN OPERATION
- TESTS ON COMPLETE HEADLAMPS
- 1. TEST FOR STABILITY OF PHOTOMETRIC PERFORMANCE
- 1.1. Clean headlamp
- 1.1.1. Test procedure
- 1.1.1.2. Test voltage
- 1.1.2. Test results
- 1.1.2.1. Visual inspection
- 1.1.2.2. Photometric test
- 1.2 Dirty headlamp
- 1.2.1. Preparation of the headlamp
- 1.2.1.1. Test mixture
- 1.2.1.2. Application of the test mixture to the headlamp
- 1.2.1.3. Measuring equipment
- 2. TEST FOR CHANGE IN VERTICAL POSITION OF THE CUT-OFF LINE UNDER THE INFLUENCE OF HEAT
- 2.1. Test
- 2.2 Test results
- 3. CONFORMITY OF PRODUCTION
- ANNEX 6
- REQUIREMENTS FOR LAMPS INCORPORATING LENSES OF PLASTIC MATERIAL — TESTING OF LENS OR MATERIAL SAMPLES AND OF COMPLETE LAMPS
- 1. GENERAL SPECIFICATIONS
- 2. TESTS
- 2.1. Resistance to temperature changes
- 2.1.1. Tests
- 2.1.2. Photometric measurements
- 2.1.2.1. Method
- 2.1.2.2. Results
- 2.2. Resistance to atmospheric and chemical agents
- 2.2.1. Resistance to atmospheric agents
- 2.2.2. Resistance to chemical agents
- 2.2.2.1. Test mixture
- 2.2.2.2. Application of the test mixture
- 2.2.2.3. Cleaning
- 2.2.3. Results
- 2.3. Resistance to detergents and hydrocarbons
- 2.3.1. Resistance to detergents
- 2.3.2. Resistance to hydrocarbons
- 2.3.3. Results
- 2.4. Resistance to mechanical deterioration
- 2.4.1. Mechanical deterioration method
- 2.4.2. Results
- 2.5. Test of adherence of coatings, if any
- 2.5.1. Preparation of the sample
- 2.5.2. Description of the test
- 2.5.3. Results
- 2.6. Tests of the complete lamp incorporating a lens of plastic material
- 2.6.1. Resistance to mechanical deterioration of the lens surface
- 2.6.1.1. Tests
- 2.6.1.2. Results
- 2.6.2. Test of adherence of coatings, if any
- 3. VERIFICATION OF THE CONFORMITY OF PRODUCTION
- Appendix 1
- A. Tests on plastic materials (lenses or samples of material supplied pursuant to paragraph 3.2.4 of this Regulation)
- B. Tests on complete lamps (supplied pursuant to paragraph 3.2.3 of this Regulation)
- Appendix 2
- Method of measurement of the diffusion and transmission of light
- 1. EQUIPMENT (see figure)
- 2. MEASUREMENTS
- Appendix 3
- Spray testing method
- 1. TEST EQUIPMENT
- 1.1. Spray qun
- 1.2. Test mixture
- 2. TEST
- Appendix 4
- Adhesive tape adherence test
- 1. PURPOSE
- 2. PRINCIPLE
- 3. SPECIFIED ATMOSPHERIC CONDITIONS
- 4. TEST PIECES
- 5. PROCEDURE
- 6. RESULTS
Feedback