Regulation No 8 of the Economic Commission for Europe of the United Nations (... (42010X0710(03))
INHALT
Regulation No 8 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen filament lamps (H1, H2, H3, HB3, HB4, H7, H8, H9, HIR1, HIR2 and/or H11)
- Regulation No 8 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen filament lamps (H1, H2, H3, HB3, HB4, H7, H8, H9, HIR1, HIR2 and/or H11)
- Revision 4
- A. ADMINISTRATIVE PROVISIONS
- B. TECHNICAL REQUIREMENTS FOR HEADLAMPS
- C. FURTHER ADMINISTRATIVE PROVISIONS
- A. ADMINISTRATIVE PROVISIONS
- 0. SCOPE(1)
- 1. DEFINITIONS
- 2. APPLICATION FOR APPROVAL OF A HEADLAMP(4)
- 3. MARKINGS(5)
- 4. APPROVAL
- 4.1. General
- 4.2. Composition of the approval mark
- 4.3. Arrangement of the approval mark
- B. TECHNICAL REQUIREMENTS FOR HEADLAMPS(8)
- 5. GENERAL SPECIFICATIONS
- 6. ILLUMINATION
- 6.1. General provisions
- 6.2. Provisions regarding passing beams
- 6.3. Provisions regarding driving beams
- 7. REQUIREMENTS CONCERNING COLOURED LENSES AND FILTERS
- 8. GAUGING DISCOMFORT
- 9. STANDARD HEADLAMP(20)
- 10. OBSERVATION CONCERNING COLOUR
- C. FURTHER ADMINISTRATIVE PROVISIONS
- 11. MODIFICATION AND EXTENSION OF APPROVAL OF A TYPE OF HEADLAMP
- 12. CONFORMITY OF PRODUCTION
- 13. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 14. PRODUCTION DEFINITELY DISCONTINUED
- 15. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
- 16. TRANSITIONAL PROVISIONS
- ANNEX 1
- COMMUNICATION
- (maximum format: A4 (210 × 297)
- ANNEX 2
- VERIFICATION OF CONFORMITY OF PRODUCTION OF HEADLAMPS EQUIPPED WITH H1, H2, H3, HB3, HB4, H7, H8, H9, HIR1, HIR2 AND/OR H11 FILAMENT LAMPS
- 1. GENERAL
- 2. MINIMUM REQUIREMENTS FOR VERIFICATION OF CONFORMITY BY THEMANUFACTURER
- 2.1. Nature of tests
- 2.2. Methods used in tests
- 2.3. Nature of sampling
- 2.4. Measured and recorded photometric characteristics
- 2.5. Criteria governing acceptability
- ANNEX 3
- EXAMPLES OF ARRANGEMENTS OF APPROVAL MARKS
- Figure 1
- Figure 3b
- Figure 10
- Simplified marking for grouped, combined or reciprocally incorporated lamps
- MODEL A
- MODEL B
- MODEL C
- MODEL D
- Figure 11
- Lamp reciprocally incorporated with a headlamp
- Example 1
- Example 2
- ANNEX 4
- MEASURING SCREENS
- A. Headlamp for right-hand traffic
- (dimensions in mm)
- B. Headlamp for left-hand traffic
- (dimensions in mm)
- C. Measuring points for illumination values
- ANNEX 5
- TESTS FOR STABILITY OF PHOTOMETRIC PERFORMANCE OF HEADLAMPS IN OPERATION
- TESTS ON COMPLETE HEADLAMPS
- 1. TEST OF STABILITY OF PHOTOMETRIC PERFORMANCE
- 1.1. Clean Headlamp
- 1.1.1. Test procedure
- 1.1.1.2. Test voltage
- 1.1.2. Test results
- 1.1.2.1. Visual inspection
- 1.1.2.2. Photometric test
- 1.2. Dirty headlamp
- 1.2.1. Preparation of the headlamp
- 1.2.1.1. Test mixture
- 1.2.1.2. Application of the test mixture to the headlamp
- 1.2.1.3. Measuring equipment
- 2. TEST FOR CHANGE IN VERTICAL POSITION OF THE CUT-OFF LINE UNDER THE INFLUENCE OF HEAT
- 2.1. Test
- 2.2. Test results
- ANNEX 6
- REQUIREMENTS FOR LAMPS INCORPORATING LENSES OF PLASTIC MATERIAL — TESTING OF LENS OR MATERIAL SAMPLES AND OF COMPLETE LAMPS
- 1. GENERAL SPECIFICATIONS
- 2. TESTS
- 2.1. Resistance to temperature changes
- 2.1.1. Tests
- 2.1.2. Photometric measurements
- 2.1.2.1. Method
- 2.1.2.2. Results
- 2.2. Resistance to atmospheric and chemical agents
- 2.2.1. Resistance to atmospheric agents
- 2.2.2. Resistance to chemical agents
- 2.2.2.1. Test mixture
- 2.2.2.2. Application of the test mixture
- 2.2.2.3. Cleaning
- 2.2.3. Results
- 2.3. Resistance to detergents and hydrocarbons
- 2.3.1. Resistance to detergents
- 2.3.2. Resistance to hydrocarbons
- 2.3.3. Results
- 2.4. Resistance to mechanical deterioration
- 2.4.1. Mechanical deterioration method
- 2.4.2. Results
- 2.5. Test of adherence of coatings, if any
- 2.5.1. Preparation of the sample
- 2.5.2. Description of the test
- 2.5.3. Results
- 2.6. Tests of the complete headlamp incorporating a lens of plastic material
- 2.6.1. Resistance to mechanical deterioration of the lens surface
- 2.6.1.1. Tests
- 2.6.1.2. Results
- 2.6.2. Test of adherence of coatings, if any
- 3. VERIFICATION OF THE CONFORMITY OF PRODUCTION
- APPENDIX 1
- CHRONOLOGICAL ORDER OF APPROVAL TESTS
- APPENDIX 2
- Method of measurement of the diffusion and transmission of light
- 1. EQUIPMENT (see figure)
- 2. MEASUREMENTS
- APPENDIX 3
- SPRAY TESTING METHOD
- 1. TEST EQUIPMENT
- 1.1. Spray gun
- 1.2. Test mixture
- 2. TEST
- APPENDIX 4
- ADHESIVE TAPE ADHERENCE TEST
- 1. PURPOSE
- 2. PRINCIPLE
- 3. SPECIFIED ATMOSPHERIC CONDITIONS
- 4. TEST PIECES
- 5. PROCEDURE
- 6. RESULTS
- ANNEX 7
- MINIMUM REQUIREMENTS FOR SAMPLING BY AN INSPECTOR
- 1. GENERAL
- 2. FIRST SAMPLING
- 2.1. The conformity is not contested
- 2.1.1.1. sample A
- 2.1.1.2. sample B
- 2.2. The conformity is contested
- 2.2.1.1. sample A
- 2.2.1.2. sample B
- 2.3. Approval withdrawn
- 2.3.1. sample A
- 2.3.2. sample B
- 3. REPEATED SAMPLING
- 3.1. The conformity is not contested
- 3.1.1.1. sample C
- 3.1.1.2. sample D
- 3.2. The conformity is contested
- 3.2.1.1. sample D
- 3.3. Approval withdrawn
- 3.3.1. sample C
- 3.3.2. sample D
- 4. CHANGE OF THE VERTICAL POSITION OF THE CUT-OFF LINE
- Figure 1
Feedback