Regulation No 118 of the Economic Commission for Europe of the United Nations... (42010X0710(07))
INHALT
Regulation No 118 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform technical prescriptions concerning the burning behaviour of materials used in the interior construction of certain categories of motor vehicles
- Regulation No 118 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform technical prescriptions concerning the burning behaviour of materials used in the interior construction of certain categories of motor vehicles
- 1. SCOPE
- 2. DEFINITIONS: General
- 3. APPLICATION FOR APPROVAL
- 4. APPROVAL
- 5. PART I — APPROVAL OF A VEHICLE TYPE WITH REGARD TO THE BURNING BEHAVIOUR OF THE INTERIOR COMPONENTS USED IN THE PASSENGER COMPARTMENT
- 5.1. Definition
- 5.2. Specifications
- 6. PART II — APPROVAL OF A COMPONENT WITH REGARD TO ITS BURNING BEHAVIOUR
- 6.1. Definitions
- 6.2. Specifications
- 7. MODIFICATION OF THE TYPE AND EXTENSION OF APPROVAL
- 8. CONFORMITY OF PRODUCTION
- 9. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 10. PRODUCTION DEFINITELY DISCONTINUED
- 11. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
- ANNEX 1
- INFORMATION DOCUMENT
- (in accordance with paragraph 3.2 of this Regulation relating to the ECE type-approval of a vehicle with regard to the burning behaviour of the interior components used in the passenger compartment)
- 1. GENERAL
- 2. GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE
- 3. BODYWORK
- ANNEX 2
- INFORMATION DOCUMENT
- (in accordance with paragraph 3.2 of the Regulation relating to the ECE type-approval of a component with regard to its burning behaviour)
- 1. GENERAL
- 2. INTERIOR MATERIALS
- ANNEX 3
- COMMUNICATION
- (Maximum format: A4 (210 × 297 mm))
- SECTION I
- GENERAL
- SECTION II
- ANNEX 4
- COMMUNICATION
- (Maximum format: A4 (210 × 297 mm))
- SECTION I
- GENERAL
- SECTION II
- ANNEX 5
- ARRANGEMENTS OF APPROVAL MARKS
- Example 1
- (see Part I of this Regulation)
- Example 2
- (see Part II of this Regulation)
- ANNEX 6
- Test to determine the horizontal burning rate of materials
- 1. Sampling and principle
- 2. Apparatus
- Figure 1
- Example of combustion chamber with sample holder and drip tray
- Figure 2
- Example of combustion chamber
- (Dimensions in millimetres)
- Figure 3
- Typical drip pan
- (Dimensions in millimetres)
- Figure 4
- Example of sample holder
- (Dimensions in millimetres)
- Figure 5
- Example of section of lower U-frame design for wire support facility
- (Dimensions in millimetres)
- 2.3. Gas burner
- 2.4. Test gas
- 3. Samples
- 3.1. Shape and dimensions
- Figure 6
- Sample
- (Dimensions in millimetres)
- 3.2. Conditioning
- 4. Procedure
- 5. Calculation
- ANNEX 7
- Test to determine the melting behaviour of materials
- 1. Sampling and principle
- 2. Apparatus
- 2.2. Calibration
- 2.2.1. Calibration check
- 2.2.2. Calibration procedure
- 3. Samples
- 4. Procedure
- 5. Results
- Figure 1
- (Dimensions in millimetres)
- ANNEX 8
- Test to determine the vertical burning rate of materials
- 1. SAMPLING AND PRINCIPLE
- 2. APPARATUS
- 3. SAMPLES
- 4. PROCEDURE
- 5. RESULTS
- Figure 1
- Specimen holder
- (Dimensions in millimetres)
- Figure 2
- Burner ignition location
- Figure 3
- Gas burner
- (Dimensions in millimetres)
Feedback