Regulation No 80 of the Economic Commission for Europe of the United Nations ... (42013X0824(01))
INHALT
Regulation No 80 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of seats of large passenger vehicles and of these vehicles with regard to the strength of the seats and their anchorages
- Regulation No 80 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of seats of large passenger vehicles and of these vehicles with regard to the strength of the seats and their anchorages
- 1. SCOPE
- 2. DEFINITIONS
- 3. APPLICATION FOR APPROVAL
- 4. APPROVAL
- 5. REQUIREMENTS FOR SEATS
- 6. REQUIREMENTS FOR SEAT ANCHORAGES OF A VEHICLE TYPE
- 7. REQUIREMENTS FOR INSTALLATION OF SEATS IN A VEHICLE TYPE
- 8. CONFORMITY OF PRODUCTION
- 9. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 10. MODIFICATION AND EXTENSION OF APPROVAL OF THE SEAT TYPE AND/OR THE VEHICLE TYPE
- 11. PRODUCTION DEFINITIVELY DISCONTINUED
- 12. TRANSITIONAL PROVISIONS
- 13. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF TYPE APPROVAL AUTHORITIES
- Appendix 1
- Test procedures for seats according to paragraph 5 and/or anchorages according to paragraph 6.1.2 and/or the installation of side-facing seats according to paragraph 3 of Appendix 7
- 1. REQUIREMENTS
- 2. PREPARATION OF THE SEAT TO BE TESTED
- 3. DYNAMIC TESTS
- 3.1. Test 1
- 3.2. Auxiliary seat
- 3.3. Manikin
- 3.4. Impact simulation
- 3.5. Test 2
- Figure 1
- Appendix 2
- TEST PROCEDURE FOR THE ANCHORAGES OF A VEHICLE IN APPLICATION OF PARAGRAPH 6.1.1
- 1. TEST APPARATUS
- 2. TEST PROCEDURE
- Appendix 3
- MEASUREMENTS TO BE MADE
- 2. Dynamic test
- 2.1. Measurements to be made on the trolley
- 2.2. Measurements to be made on manikins
- Appendix 4
- DETERMINATION OF ACCEPTABILITY CRITERIA
- 1. FRONTAL IMPACT (FORWARD-FACING SEAT)
- 1.1. Head acceptability criterion (HIC)
- 1.2. Thorax acceptability criterion (ThAC)
- 1.3. Femur acceptability criterion (FAC)
- 2. SIDE IMPACT (SIDE-FACING SEAT)
- 2.1. Head acceptability criterion (HIC) see above paragraph 1.1.
- 2.2. Thorax acceptability criterion
- 2.3. Abdomen acceptability criterion
- 2.4. Pelvis acceptability criterion
- Appendix 5
- STATIC TEST REQUIREMENTS AND PROCEDURE
- 1. REQUIREMENTS
- 2. STATIC TESTS
- 2.1. Test apparatus
- 2.2. Test procedure
- Figure 1
- Static test apparatus
- Appendix 6
- ENERGY ABSORPTION CHARACTERISTICS OF THE REAR PART OF SEAT BACKS
- Appendix 7
- REQUIREMENTS FOR THE SAFEGUARDING OF PASSENGERS IN SIDE-FACING SEATS ACCORDING TO PARAGRAPH 7.4.4
- Figure 1
- Positioning requirements for side-facing seats
- Figure 2
- Positioning requirements for the vehicle part forward of the foremost side-facing seat
- ANNEX 1
- COMMUNICATION
- (Maximum format: A4 (210 × 297 mm))
- ANNEX 2
- COMMUNICATION
- (Maximum format: A4 (210 × 297 mm))
- ANNEX 3
- ARRANGEMENTS OF APPROVAL MARKS
- 1. Arrangement in the approval mark for a seat
- 2. Arrangement in the approval mark for a vehicle type
- ANNEX 4
- Procedure for determining the ‘H’ point and the actual torso angle for seating position in motor vehicles
- (1)
Feedback