Regulation No 123 of the Economic Commission for Europe of the United Nations... (42010X0824(01))
INHALT
Regulation No 123 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of adaptive front-lighting systems (AFS) for motor vehicles
- Regulation No 123 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of adaptive front-lighting systems (AFS) for motor vehicles
- A. ADMINISTRATIVE PROVISIONS
- B. TECHNICAL REQUIREMENTS FOR SYSTEMS
- C. FURTHER ADMINISTRATIVE PROVISIONS
- A. ADMINISTRATIVE PROVISIONS
- 0. SCOPE
- 1. DEFINITIONS
- 2. APPLICATION FOR APPROVAL OF A SYSTEM
- 3. MARKINGS
- 4. APPROVAL
- 4.1. General
- 4.2. Composition of the approval mark
- 4.3. Arrangement of the approval mark
- 4.3.1. Independent lamps
- 4.3.2. Grouped, combined or reciprocally incorporated lamps
- B. TECHNICAL REQUIREMENTS FOR SYSTEMS OR PART(S) OF A SYSTEM
- 5. GENERAL SPECIFICATIONS
- 6. ILLUMINATION
- 6.1. General provisions
- 6.2. Provisions concerning passing beam
- 6.3. Provisions concerning driving beam
- 6.4. Other provisions
- 7. COLOUR
- C. FURTHER ADMINISTRATIVE PROVISIONS
- 8. MODIFICATION OF THE SYSTEM TYPE AND EXTENSION OF APPROVAL
- 9. CONFORMITY OF PRODUCTION
- 10. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 11. PRODUCTION DEFINITELY DISCONTINUED
- 12. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF ADMINISTRATIVE DEPARTMENTS
- ANNEX 1
- COMMUNICATION
- (maximum format: A4 (210 × 297 mm))
- ANNEX 2
- EXAMPLES OF ARRANGEMENTS OF APPROVAL MARKS
- Example 1
- Example 2
- Example 3
- Example 4
- Example 5
- Identification of an installation unit incorporating a lens of plastic material meeting the requirements of this Regulation
- Example 6
- Installation unit 1
- Installation unit 3
- Installation unit 1 of the system
- Figure 11
- Installation unit 3 of the system
- Example 7
- Arrangement of approval marks relative to a system (Figure 12)
- Figure 12
- Example 8
- Arrangement of approval marks relative to both sides of a system (Figure 13)
- Figure 13
- Figure 14
- ANNEX 3
- PASSING BEAM PHOTOMETRIC REQUIREMENTS
- (1)
- Figure 1
- Angular positions of passing beam photometric requirements (indicated for right-hand traffic)
- Appendix to Table 1
- ANNEX 4
- Tests for stability of photometric performance of systems in operation
- TESTS ON COMPLETE SYSTEMS
- 1. TEST FOR STABILITY OF PHOTOMETRIC PERFORMANCE
- 1.1. Clean test sample
- 1.1.1. Test procedure
- 1.1.1.1. Test sequence
- 1.1.1.2. Test voltage
- 1.1.2. Test results
- 1.1.2.1. Visual inspection:
- 1.1.2.2. Photometric test:
- 1.2. Dirty test sample
- 1.2.1. Preparation of the test sample
- 1.2.1.3. Particle-size distribution
- 2. TEST FOR CHANGE IN VERTICAL POSITION OF THE ‘CUT-OFF’ LINE UNDER THE INFLUENCE OF HEAT
- 2.1. Test
- 2.2. Test results
- ANNEX 5
- Minimum requirements for conformity of production control procedures
- 1. GENERAL
- 2. MINIMUM REQUIREMENTS FOR VERIFICATION OF CONFORMITY BY THE MANUFACTURER
- 2.1. Nature of tests
- 2.2. Methods used in tests
- 2.3. Nature of sampling
- 2.4. Measured and recorded photometric characteristics
- 2.5. Criteria governing acceptability
- ANNEX 6
- Requirements for systems incorporating lenses of plastic material: testing of lens or material samples and complete systems or part(s) of systems
- 1. GENERAL SPECIFICATIONS
- 2. TESTS
- 2.1. Resistance to temperature changes
- 2.1.1. Tests
- 2.1.2. Photometric measurements
- 2.1.2.1. Method
- 2.1.2.2. Results
- 2.2. Resistance to atmospheric and chemical agents
- 2.2.1. Resistance to atmospheric agents
- 2.2.2. Resistance to chemical agents
- 2.2.2.1. Test mixture
- 2.2.2.2. Application of the test mixture
- 2.2.2.3. Cleaning
- 2.2.3. Results
- 2.2.4. Resistance to light source radiation
- 2.3. Resistance to detergents and hydrocarbons
- 2.3.1. Resistance to detergents
- 2.3.2. Resistance to hydrocarbons
- 2.3.3. Results
- 2.4. Resistance to mechanical deterioration
- 2.4.1. Mechanical deterioration method
- 2.4.2. Results
- 2.5. Test of adherence of coatings, if any
- 2.5.1. Preparation of the sample
- 2.5.2. Description of the test
- 2.5.3. Results
- 2.6. Tests of the complete system incorporating a lens of plastic material
- 2.6.1. Resistance to mechanical deterioration of the lens surface
- 2.6.1.1. Tests
- 2.6.1.2. Results
- 2.6.2. Test of adherence of coatings, if any
- 3. VERIFICATION OF THE CONFORMITY OF PRODUCTION
- APPENDIX 1
- CHRONOLOGICAL ORDER OF APPROVAL TESTS
- APPENDIX 2
- Method of measurement of the diffusion and transmission of light
- 1. EQUIPMENT (see Figure 1 below)
- Figure 1
- Optical set up for measurement of variations in diffusion and transmission
- 2. MEASUREMENTS
- APPENDIX 3
- SPRAY TESTING METHOD
- 1. TEST EQUIPMENT
- 1.1. Spray gun
- 1.2. Test mixture
- 2. TEST
- APPENDIX 4
- ADHESIVE TAPE ADHERENCE TEST
- 1. PURPOSE
- 2. PRINCIPLE
- 3. SPECIFIED ATMOSPHERIC CONDITIONS
- 4. TEST PIECES
- 5. PROCEDURE
- 6. RESULTS
- ANNEX 7
- MINIMUM REQUIREMENTS FOR SAMPLING BY AN INSPECTOR
- 1. GENERAL
- 2. FIRST SAMPLING
- 2.1. The conformity is not contested
- 2.1.1.1. Sample A
- 2.1.1.2. Sample B
- 2.2. The conformity is not contested
- 2.2.1.1. Sample A
- 2.2.1.2. Sample B
- 2.3. Approval withdrawn
- 2.3.1. Sample A
- 2.3.2. Sample B
- 3. REPEATED SAMPLING
- 3.1. The conformity is not contested
- 3.1.1.1. Sample C
- 3.1.1.2. Sample D
- 3.2. The conformity is not contested
- 3.2.1.1. Sample D
- 3.3. Approval withdrawn
- 3.3.1. Sample C
- 3.3.2. Sample D
- 4. CHANGE OF THE VERTICAL POSITION OF THE CUT-OFF LINE FOR PASSING BEAM
- Figure 1
- ANNEX 8
- PASSING BEAM ‘CUT-OFF’ AND AIMING PROVISIONS
- (1)
- 1. CUT-OFF DEFINITION
- 1.1. Shape (see Fig. A.8-1)
- 2. VISUAL AIMING PROCEDURE
- Figures
- ANNEX 9
- PHOTOMETRIC MEASUREMENT PROVISIONS
- 1. GENERAL PROVISIONS
- 2. MEASUREMENT CONDITIONS WITH RESPECT TO LIGHT SOURCES
- 3. MEASUREMENT CONDITIONS WITH RESPECT TO BENDING MODES
- ANNEX 10
- DESCRIPTION FORMS
- maximum format: A4 (210 × 297 mm)
- ANNEX 11
- Requirements for LED modules and AFS including LED modules
- 1. GENERAL SPECIFICATIONS
- 2. MANUFACTURE
- 3. TEST CONDITIONS
- 3.1. Application
- 3.2. Operating conditions
- 3.2.1. LED module operating conditions
- 3.2.2. Ambient temperature
- 3.3. Ageing
- 4. SPECIFIC SPECIFICATIONS AND TESTS
- 4.1. Colour rendering
- 4.1.1. Red content
- 4.2. UV-radiation
- 4.3. Temperature stability
- 4.3.1. Illuminance
- 4.3.2. Colour
Feedback