INHALT

Regulation No 11 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with regard to door latches and door retention components

Regulation No 11 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with regard to door latches and door retention components
1. SCOPE
2. DEFINITIONS
3. APPLICATION FOR APPROVAL
4. APPROVAL
5. GENERAL REQUIREMENTS
5.2. Door latches
6. PERFORMANCE REQUIREMENTS
6.1. Hinged doors
6.1.1. Load test one
6.1.2. Load test two
6.1.3. Load test three (applicable to doors that open in a vertical direction)
6.1.4. Inertial load.
6.1.5. Door hinges
6.2. Sliding side doors
6.2.1. Load test one
6.2.2. Load test two
6.2.3. Inertial load
6.2.4. Door system
6.3. Door locks
6.3.2. Rear side doors
6.3.3. Back doors
7. TEST PROCEDURES
7.1. Hinged doors
7.1.1. Door latches
7.1.1.1. Load tests one, two, and three, force application
7.1.1.2. Inertial force application
7.1.2. Door hinges
7.2. Sliding side doors
7.2.1. Door latches
7.2.1.1. Load tests one and two, force application
7.2.1.2. Inertial force application
7.2.2. Door system
8. MODIFICATION AND EXTENSION OF APPROVAL OF THE VEHICLE TYPE
9. CONFORMITY OF PRODUCTION
10. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
11. PRODUCTION DEFINITELY DISCONTINUED
12. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
13. TRANSITIONAL PROVISIONS
ANNEX 1
COMMUNICATION
(Maximum format: A4 (210 × 297 mm))
ANNEX 2
ARRANGEMENTS OF APPROVAL MARKS
MODEL A
(See paragraph 4.4 of this Regulation)
MODEL B
(See paragraph 4.5 of this Regulation)
ANNEX 3
LATCH TEST FOR LOAD TESTS ONE, TWO, AND THREE, FORCE APPLICATION
1. PURPOSE
2. TEST OPERATION
2.1. Load test one
2.1.2. Procedures
2.1.2.1. Fully latched position
2.1.2.2. Secondary latched position
2.2. Load test two
2.2.2. Procedures
2.2.2.1. Fully latched position
2.2.2.2. Secondary latched position
2.3. Load test three (for doors that open in a vertical direction)
2.3.2. Procedure
Figure 3-1
Door latch — Tensile testing fixture for load test one
Figure 3-2
Door latch — Tensile testing fixture for load test two
Figure 3-3
Door latch — Tensile testing fixture for load test three (for doors that open in a vertical direction)
Figure 3-4
Door static load test directions
ANNEX 4
INERTIAL TEST PROCEDURES
1. PURPOSE
2. TEST PROCEDURES
2.2. Option 2, Full Vehicle Dynamic Test
2.2.1. Test equipment
2.2.2. Test setup
2.2.3. Test directions (see Figure 4-3)
2.3. Option 3, Door Dynamic Test
2.3.1. Test equipment
2.3.2. Test setup
2.3.3. Test directions (see Figure 4-3)
2.4. Test operation for Options 2 and 3
Figure 4-1
Inertial loading — Sample calculation
Table 4-1
Acceleration Pulse Corridor
Figure 4-2
Acceleration Pulse
Figure 4-3
Vehicle coordinate reference system for inertial testing
ANNEX 5
HINGE TEST PROCEDURE
1. PURPOSE
2. TEST PROCEDURE
2.1. Multiple Hinge System
2.1.1. Longitudinal load test
2.1.1.1. Equipment
2.1.1.2. Procedure
2.1.2. Transverse load test
2.1.2.1. Equipment
2.1.2.2. Procedure
2.1.3. Vertical load test (for doors that open in the vertical direction)
2.1.3.1. Equipment
2.1.3.2. Procedure
2.2.1. Test procedures
Figure 5-1
Static test fixtures
Figure 5-2
Static load test directions for doors that open in the vertical direction
ANNEX 6
SLIDING SIDE DOOR
Full door test
1. PURPOSE
2. GENERAL PROVISIONS
3. TEST SETUP
4. TEST PROCEDURE
Figure 6-1
Sliding side door full vehicle test procedure (note: sliding door is shown separated from the vehicle)