Regulation No 19 of the Economic Commission for Europe of the United Nations ... (42010X0710(04))
INHALT
Regulation No 19 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of power-driven vehicle front fog lamps
- Regulation No 19 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of power-driven vehicle front fog lamps
- INTRODUCTION
- 0. SCOPE
- 1. DEFINITIONS
- 2. APPLICATION FOR APPROVAL
- 3. MARKINGS
- 4. APPROVAL
- 4.1. General
- 4.2. Composition of the approval mark
- 4.3. Arrangement of the approval mark
- 4.3.1. Independent lamps
- 4.3.2. Grouped, combined or reciprocally incorporated lamps
- 5. GENERAL SPECIFICATIONS
- 6. ILLUMINATION
- 6.4. In the case of Class F3 front fog lamps
- 6.4.3. Photometric requirements
- 7. COLOUR
- 8. DETERMINATION OF DISCOMFORT (DAZZLE)
- 9. MODIFICATIONS OF THE TYPE OF FRONT FOG LAMP AND EXTENSION OF APPROVAL
- 10. CONFORMITY OF PRODUCTION
- 11. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 12. PRODUCTION DEFINITELY DISCONTINUED
- 13. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF ADMINISTRATIVE DEPARTMENTS
- 14. TRANSITIONAL PROVISIONS
- ANNEX 1
- COMMUNICATION FORM
- (Maximum format: A4 (210 × 297 mm))
- ANNEX 2
- Tolerance requirements for conformity of production control procedure
- ANNEX 3
- Examples of arrangements of approval marks for front fog lamps of class B
- Figure 1
- Figure 2a
- Figure 2b
- Examples of possible markings for grouped, combined or reciprocally incorporated lamps situated on the front of a vehicle
- Figure 3
- Lamp reciprocally incorporated with a headlamp
- Figure 4
- Figure 5
- Lighting device used either as front fog lamp or as reversing lamp
- Figure 6
- Examples of arrangements of approval marks for front fog lamps of class ‘F3’
- Figure 7
- Examples of possible markings for grouped, combined or reciprocally incorporated lamps situated on the front of a vehicle
- Figure 9
- Lighting device used either as front fog lamp or as reversing lamp
- Figure 10
- Front fog lamp reciprocally incorporated with a headlamp
- Figure 11
- Figure 12
- Led modules
- Figure 13
- Front fog lamps as a matched pair
- Figure 14
- ANNEX 4
- MEASURING SCREEN GEOMETRY AND MEASURING GRID
- 1. MEASURING SCREEN
- Figure 1
- 2. MEASURING GRID (see Figure 2)
- Figure 2
- Light distribution of the Class B front fog lamp
- Figure 3
- Light distribution of the Class F3 front fog lamp
- ANNEX 5
- Tests for stability of photometric performance of front fog lamps in operation (tests on complete front fog lamps)
- 1. TEST FOR STABILITY OF PHOTOMETRIC PERFORMANCE
- 1.1. Clean front fog lamp
- 1.1.1. Test procedure
- 1.1.2. Test voltage
- 1.1.3. Test results
- 1.1.3.1. Visual inspection
- 1.1.3.2. Photometric test
- 1.2. Dirty front fog lamp
- 1.2.1. Preparation of the front fog lamp
- 1.2.1.1. Test mixture
- 1.2.1.2. Application of the test mixture to the front fog lamp
- 2. TEST FOR CHANGE IN VERTICAL POSITION OF THE CUT-OFF LINE UNDER THE INFLUENCE OF HEAT
- 2.1. Test
- 2.2. Test results
- ANNEX 6
- Requirements for lamps incorporating lenses of plastic material - testing of lens or material samples and of complete lamps
- 1. GENERAL SPECIFICATIONS
- 2. TESTS
- 2.1. Resistance to temperature changes
- 2.1.1. Tests
- 2.1.2. Photometric measurements
- 2.1.2.1. Method
- 2.1.2.2. Results
- 2.2. Resistance to atmospheric and chemical agents
- 2.2.1. Resistance to atmospheric agents
- 2.2.2. Resistance to chemical agents
- 2.2.2.1. Test mixture
- 2.2.2.2. Application of the test mixture
- 2.2.2.3. Cleaning
- 2.2.3. Results
- 2.3. Resistance to detergents and hydrocarbons
- 2.3.1. Resistance to detergents
- 2.3.2. Resistance to hydrocarbons
- 2.3.3. Results
- 2.4. Resistance to mechanical deterioration
- 2.4.1. Mechanical deterioration method
- 2.4.2. Results
- 2.5. Test of adherence of coatings, if any
- 2.5.1. Preparation of the sample
- 2.5.2. Description of the test
- 2.5.3. Results
- 2.6. Tests of the complete lamp incorporating a lens of plastic material
- 2.6.1. Resistance to mechanical deterioration of the lens surface
- 2.6.1.1. Tests
- 2.6.1.2. Results
- 2.6.2. Test of adherence of coatings, if any
- 2.7. Resistance to light source radiation
- 3. VERIFICATION OF THE CONFORMITY OF PRODUCTION
- APPENDIX 1
- CHRONOLOGICAL ORDER OF APPROVAL TESTS
- APPENDIX 2
- Method of measurement of the diffusion and transmission of light
- 1. EQUIPMENT (SEE FIGURE)
- 2. MEASUREMENTS
- APPENDIX 3
- SPRAY TESTING METHOD
- 1. TEST EQUIPMENT
- 1.1. Spray gun
- 1.2. Test mixture
- 2. TEST
- APPENDIX 4
- ADHESIVE TAPE ADHERENCE TEST
- 1. PURPOSE
- 2. PRINCIPLE
- 3. SPECIFIED ATMOSPHERIC CONDITIONS
- 4. TEST PIECES
- 5. PROCEDURE
- 6. RESULTS
- ANNEX 7
- Minimum requirements for conformity of production control procedure
- 1. GENERAL
- 2. MINIMUM REQUIREMENTS FOR VERIFICATION OF CONFORMITY BY THE MANUFACTURER
- 2.1. Nature of tests
- 2.2. Methods used in tests
- 2.3. Nature of sampling
- 2.4. Measured and recorded photometric characteristics
- 2.5. Criteria governing acceptability
- ANNEX 8
- MINIMUM REQUIREMENTS FOR SAMPLING BY AN INSPECTOR
- 1. GENERAL
- 2. FIRST SAMPLING
- 2.1. Conformity is not contested
- 2.1.1.1. sample A
- 2.1.1.2. sample B
- 2.2. Conformity is contested
- 2.2.1.1. sample A
- 2.2.1.2. sample B
- 2.3. Approval withdrawn
- 2.3.1. sample A
- 2.3.2. sample B
- 3. REPEATED SAMPLING
- 3.1. Conformity is not contested
- 3.1.1.1. sample C
- 3.1.1.2. sample D
- 3.2. Conformity is contested
- 3.3. Approval withdrawn
- 3.3.1. sample C
- 3.3.2. sample D
- 4. CHANGE OF THE VERTICAL POSITION OF THE CUT-OFF LINE
- Figure 1
- ANNEX 9
- Definition and sharpness of the cut-off line and aiming procedure by means of this cut-off line for class F3 front fog lamps
- 1. GENERAL
- 2. SHAPE OF THE CUT-OFF LINE
- Figure 1
- Shape and position of the ‘cut-off’ line
- 3. ADJUSTMENT OF THE FRONT FOG LAMP
- 3.1. Horizontal adjustment
- 3.2. Vertical adjustment
- 4. MEASUREMENT OF THE QUALITY OF CUT-OFF
- 4.1.3. Linearity
- 5. INSTRUMENTAL VERTICAL ADJUSTMENT
- ANNEX 10
- Overview of operational periods concerning test for stability of photometric performance
- ANNEX 11
- CENTRE OF REFERENCE
- Diameter = a = 2 mm min.
- ANNEX 12
- Requirements in case of use of led module(s) or of light-generators
- 1. GENERAL SPECIFICATIONS
- 2. MANUFACTURE
- 3. TEST CONDITIONS
- 3.1. Application and relaxation
- 3.1.3. Operating conditions
- 3.1.4. Ambient temperature
- 3.1.5.1. Power supply
- 3.1.5.2. Burning position
- 3.2. Ageing
- 3.2.3. LED module(s)
- 3.2.4. Filament lamps
- 3.2.5. Gas discharge light sources
- 4. SPECIFIC TESTS
- 4.2. Gas discharge light sources
- 4.3. Run-up
- 4.3.2. Gas discharge light sources
- 4.4. Hot re-strike
- 4.4.2. Gas discharge light sources
- 4.5. Colour rendering
- 4.5.1. Red content
- 4.6. UV-radiation
- 4.7. Temperature stability
- 4.7.1. Luminous intensity
- 4.7.2. Colour
Feedback