COMMISSION IMPLEMENTING DECISION (EU) 2023/2723
of 6 December 2023
on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council
(Text with EEA relevance)
Article 1
Article 2
Article 3
Article 4
ANNEX I
No |
Reference of the standard |
1. |
HD 308 S2:2001 Identification of cores in cables and flexible cords |
2. |
HD 368 S1:1978 Direct acting recording electrical measuring instruments and their accessories |
3. |
HD 549 S1:1989 Conference systems – Electrical and audio requirements |
4. |
HD 597 S1:1992 Coupling capacitors and capacitor dividers HD 597 S1:1992/AC:1992 |
5. |
HD 603 S1:1994 Distribution cables of rated voltage 0,6/1 kV HD 603 S1:1994/A3:2007 HD 603 S1:1994/A1:1997 HD 603 S1:1994/A2:2003 |
6. |
HD 604 S1:1994 0,6/1 kV and 1,9/3,3 kV power cables with special fire performance for use in power stations HD 604 S1:1994/A3:2005 HD 604 S1:1994/A1:1997 HD 604 S1:1994/A2:2002 |
7. |
HD 626 S1:1996 Overhead distribution cables of rated voltage Uo/U(Um): 0,6/1 (1,2) kV HD 626 S1:1996/A1:1997 HD 626 S1:1996/A2:2002 |
8. |
HD 627 S1:1996 Multicore and multipair cables for installation above and below ground HD 627 S1:1996/A1:2000 HD 627 S1:1996/A2:2005 |
9. |
HD 639 S1:2002 Electrical accessories – Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs) HD 639 S1:2002/A1:2003 HD 639 S1:2002/A2:2010 HD 639 S1:2002/AC:2003 |
10. |
EN ISO 11252:2013 Lasers and laser-related equipment – Laser device – Minimum requirements for documentation (ISO 11252:2013) |
11. |
EN 13637:2015 Building hardware – Electrically controlled exit systems for use on escape routes – Requirements and test methods |
12. |
EN 50065-4-2:2001 Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz – Part 4-2: Low voltage decoupling filters – Safety requirements EN 50065-4-2:2001/A1:2003 EN 50065-4-2:2001/A2:2005 |
13. |
EN 50065-4-7:2005 Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz – Part 4-7: Portable low voltage decoupling filters – Safety requirements EN 50065-4-7:2005/AC:2006 |
14. |
EN 50085-1:2005 Cable trunking systems and cable ducting systems for electrical installations – Part 1: General requirements EN 50085-1:2005/A1:2013 |
15. |
EN 50085-2-1:2006 Cable trunking systems and cable ducting systems for electrical installations – Part 2-1: Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings EN 50085-2-1:2006/A1:2011 |
16. |
EN 50085-2-2:2008 Cable trunking systems and cable ducting systems for electrical installations – Part 2-2: Particular requirements for cable trunking systems and cable ducting systems intended for mounting underfloor, flushfloor, or onfloor |
17. |
EN 50085-2-3:2010 Cable trunking systems and cable ducting systems for electrical installations – Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets |
18. |
EN 50085-2-4:2009 Cable trunking systems and cable ducting systems for electrical installations – Part 2-4: Particular requirements for service poles and service posts |
19. |
EN 50106:2008 Safety of household and similar electrical appliances – Particular rules for routine tests referring to appliances under the scope of EN 60335-1 |
20. |
EN 50117-1:2002 Coaxial cables – Part 1: Generic specification EN 50117-1:2002/A1:2006 EN 50117-1:2002/A2:2013 |
21. |
EN 50117-2-1:2005 Coaxial cables – Part 2-1: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 1 000 MHz EN 50117-2-1:2005/A1:2008 EN 50117-2-1:2005/A2:2013 |
22. |
EN 50117-2-2:2004 Coaxial cables – Part 2-2: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 1 000 MHz EN 50117-2-2:2004/A1:2008 EN 50117-2-2:2004/A2:2013 |
23. |
EN 50117-2-3:2004 Coaxial cables – Part 2-3: Sectional specification for cables used in cabled distribution networks – Distribution and trunk cables for systems operating at 5 MHz – 1 000 MHz EN 50117-2-3:2004/A1:2008 EN 50117-2-3:2004/A2:2013 |
24. |
EN 50117-2-4:2004 Coaxial cables – Part 2-4: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz EN 50117-2-4:2004/A1:2008 EN 50117-2-4:2004/A2:2013 |
25. |
EN 50117-2-5:2004 Coaxial cables – Part 2-5: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 3 000 MHz EN 50117-2-5:2004/AC:2012 EN 50117-2-5:2004/A1:2008 EN 50117-2-5:2004/A2:2013 |
26. |
EN 50117-3-1:2002 Coaxial cables – Part 3-1: Sectional specifications for cables used in Telecom applications – Miniaturized cables used in digital communication systems |
27. |
EN 50117-4-1:2008 Coaxial cables – Part 4-1: Sectional specification for cables for BCT cabling in accordance with EN 50173 – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz EN 50117-4-1:2008/A1:2013 |
28. |
EN 50117-4-2:2015 Coaxial cables – Part 4-2: Sectional specification for CATV cables up to 6 GHz used in cabled distribution networks |
29. |
EN 50156-1:2015 Electrical equipment for furnaces and ancillary equipment – Part 1: Requirements for application design and installation |
30. |
EN 50156-2:2015 Electrical equipment for furnaces and ancillary equipment – Part 2: Requirements for design, development and type approval of safety devices and subsystems |
31. |
EN 50214:2006 Flat polyvinyl chloride sheathed flexible cables EN 50214:2006/AC:2007 |
32. |
EN 50250:2002 Conversion adaptors for industrial use EN 50250:2002/A1:2015 EN 50250:2002/AC:2007 |
33. |
EN 50274:2002 Low-voltage switchgear and controlgear assemblies – Protection against electric shock – Protection against unintentional direct contact with hazardous live parts EN 50274:2002/AC:2009 |
34. |
EN 50288-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 1: Generic specification |
35. |
EN 50288-2-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 2-1: Sectional specification for screened cables characterised up to 100 MHz – Horizontal and building backbone cables |
36. |
EN 50288-2-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 2-2: Sectional specification for screened cables characterised up to 100 MHz – Work area and patch cord cables |
37. |
EN 50288-3-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 3-1: Sectional specification for unscreened cables characterised up to 100 MHz – Horizontal and building backbone cables |
38. |
EN 50288-3-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz – Work area and patch cord cables |
39. |
EN 50288-4-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 4-1: Sectional specification for screened cables characterised up to 600 MHz – Horizontal and building backbone cables |
40. |
EN 50288-4-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 4-2: Sectional specification for screened cables characterised up to 600 MHz – Work area and patch cord cables |
41. |
EN 50288-5-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 5-1: Sectional specification for screened cables characterized up to 250 MHz – Horizontal and building backbone cables |
42. |
EN 50288-5-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 5-2: Sectional specification for screened cables characterized up to 250 MHz – Work area and patch cord cables |
43. |
EN 50288-6-1:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 6-1: Sectional specification for unscreened cables characterised up to 250 MHz – Horizontal and building backbone cables |
44. |
EN 50288-6-2:2013 Multi-element metallic cables used in analogue and digital communication and control – Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz – Work area and patch cord cables |
45. |
EN 50288-7:2005 Multi-element metallic cables used in analogue and digital communication and control – Part 7: Sectional specification for instrumentation and control cables |
46. |
EN 50288-8:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 8: Specification for type 1 cables characterised up to 2 MHz |
47. |
EN 50288-9-1:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 9-1: Sectional specification for screened cables characterised up to 1 000 MHz – Horizontal and building backbone cables |
48. |
EN 50288-9-2:2015 Multi-element metallic cables used in analogue and digital communication and control – Part 9-2: Sectional specification for screened cables characterized from 1 MHz up to 1 000 MHz for work area, patch cord and data centre applications |
49. |
EN 50288-10-1:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 10-1: Sectional specification for screened cables characterized up to 500 MHz – Horizontal floor and building backbone cables |
50. |
EN 50288-10-2:2015 Multi-element metallic cables used in analogue and digital communication and control – Part 10-2: Sectional specification for screened cables characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications |
51. |
EN 50288-11-1:2012 Multi-element metallic cables used in analogue and digital communication and control – Part 11-1: Sectional specification for un-screened cables characterised up to 500 MHz – Horizontal and building backbone cables |
52. |
EN 50288-11-2:2015 Multi-element metallic cables used in analogue and digital communication and control – Part 11-2: Sectional specification for un-screened cables, characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications |
53. |
EN 50289-1-3:2001 Communication cables – Specifications for test methods – Part 1-3: Electrical test methods – Dielectric strength |
54. |
EN 50289-1-4:2001 Communication cables – Specifications for test methods – Part 1-4: Electrical test methods – Insulation resistance |
55. |
EN 50290-2-1:2005 Communication cables – Part 2-1: Common design rules and construction |
56. |
EN 50290-2-20:2001 Communication cables – Part 2-20: Common design rules and construction – General |
57. |
EN 50290-2-21:2001 Communication cables – Part 2-21: Common design rules and construction – PVC insulation compounds EN 50290-2-21:2001/A1:2007/AC:2016 EN 50290-2-21:2001/A1:2007 EN 50290-2-21:2001/AC:2003 |
58. |
EN 50290-2-22:2001 Communication cables – Part 2-22: Common design rules and construction – PVC sheathing compounds EN 50290-2-22:2001/A1:2007 |
59. |
EN 50290-2-23:2013 Communication cables – Part 2-23: Common design rules and construction – Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables |
60. |
EN 50290-2-24:2002 Communication cables – Part 2-24: Common design rules and construction – PE sheathing EN 50290-2-24:2002/A1:2008 |
61. |
EN 50290-2-25:2013 Communication cables – Part 2-25: Common design rules and construction – Polypropylene insulation compounds |
62. |
EN 50290-2-26:2002 Communication cables – Part 2-26: Common design rules and construction – Halogen free flame retardant insulation compounds EN 50290-2-26:2002/A1:2007 |
63. |
EN 50290-2-27:2002 Communication cables – Part 2-27: Common design rules and construction – Halogen free flame retardant thermoplastic sheathing compounds EN 50290-2-27:2002/A1:2007 EN 50290-2-27:2002/A1:2007/AC:2010 |
64. |
EN 50290-2-28:2002 Communication cables – Part 2-28: Common design rules and construction – Filling compounds for filled cables |
65. |
EN 50290-2-29:2002 Communication cables – Part 2-29: Common design rules and construction – Cross-linked PE insulation compounds |
66. |
EN 50290-2-30:2002 Communication cables – Part 2-30: Common design rules and construction – Poly(tetrafluoroethylene-hexafluoropropylene) (FEP) insulation and sheathing |
67. |
EN 50290-4-1:2014 Communication cables – Part 4-1: General considerations for the use of cables – Environmental conditions and safety aspects |
68. |
EN 50290-4-2:2014 Communication cables – Part 4-2: General considerations for the use of cables – Guide to use |
69. |
EN 50364:2010 Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications |
70. |
EN 50369:2005 Liquid tight sheathing systems for cable management |
71. |
EN 50406-1:2004 End user multi-pair cables used in high bit rate telecommunication networks – Part 1: Aerial cables |
72. |
EN 50406-2:2004 End user multi-pair cables used in high bit rate telecommunication networks – Part 2: Duct and buried cables |
73. |
EN 50407-1:2004 Multi-pair cables used in high bit rate digital access telecommunication networks – Part 1: Outdoor cables |
74. |
EN 50407-3:2014 Multi-pair cables used in high bit rate digital access telecommunications networks – Part 3: Indoor multi-pair/quad riser cables up to 100 MHz for maximum length of connection 100 m supporting universal services, xDSL and applications up to 100 Mbit/s over IP |
75. |
EN 50428:2005 Switches for household and similar fixed electrical installations – Collateral standard – Switches and related accessories for use in home and building electronic systems (HBES) EN 50428:2005/A1:2007 EN 50428:2005/A2:2009 |
76. |
EN 50441-1:2012 Cables for indoor residential telecommunication installations – Part 1: Unscreened cables – Grade 1 |
77. |
EN 50441-2:2012 Cables for indoor residential telecommunication installations – Part 2: Screened cables – Grade 1 |
78. |
EN 50441-3:2006 Cables for indoor residential telecommunication installations – Part 3: Screened cables – Grade 3 |
79. |
EN 50441-4:2012 Cables for indoor residential telecommunication installations – Part 4: Cables up to 1 200 MHz – Grade 3 |
80. |
EN 50445:2008 Product family standard to demonstrate compliance of equipment for resistance welding, arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic fields (0 Hz – 300 GHz) |
81. |
EN 50491-4-1:2012 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 4-1: General functional safety requirements for products intended to be integrated in Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) |
82. |
EN 50491-6-1:2014 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 6-1: HBES installations – Installation and planning |
83. |
EN 50520:2020 Cover plates and cover tapes for the protection and location warning of buried cables or buried conduits in underground installations EN 50520:2020/A1:2021 |
84. |
EN 50525-1:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 1: General requirements |
85. |
EN 50525-2-11:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-11: Cables for general applications – Flexible cables with thermoplastic PVC insulation |
86. |
EN 50525-2-12:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-12: Cables for general applications – Cables with thermoplastic PVC insulation for extensible leads |
87. |
EN 50525-2-21:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-21: Cables for general applications – Flexible cables with crosslinked elastomeric insulation EN 50525-2-21:2011/AC:2013 |
88. |
EN 50525-2-22:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-22: Cables for general applications – High flexibility braided cables with crosslinked elastomeric insulation |
89. |
EN 50525-2-31:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-31: Cables for general applications – Single core non-sheathed cables with thermoplastic PVC insulation |
90. |
EN 50525-2-41:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-41: Cables for general applications – Single core cables with crosslinked silicone rubber insulation |
91. |
EN 50525-2-42:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-42: Cables for general applications – Single core non-sheathed cables with crosslinked EVA insulation |
92. |
EN 50525-2-51:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-51: Cables for general applications – Oil resistant control cables with thermoplastic PVC insulation |
93. |
EN 50525-2-71:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-71: Cables for general applications – Flat tinsel cables (cords) with thermoplastic PVC insulation |
94. |
EN 50525-2-72:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-72: Cables for general applications – Flat divisible cables (cords) with thermoplastic PVC insulation |
95. |
EN 50525-2-81:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-81: Cables for general applications – Cables with crosslinked elastomeric covering for arc welding |
96. |
EN 50525-2-82:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-82: Cables for general applications – Cables with crosslinked elastomeric insulation for decorative chains |
97. |
EN 50525-2-83:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-83: Cables for general applications – Multicore cables with crosslinked silicone rubber insulation |
98. |
EN 50525-3-11:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-11: Cables with special fire performance – Flexible cables with halogen-free thermoplastic insulation, and low emission of smoke |
99. |
EN 50525-3-21:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-21: Cables with special fire performance – Flexible cables with halogen-free crosslinked insulation, and low emission of smoke EN 50525-3-21:2011/AC:2013 |
100. |
EN 50525-3-31:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-31: Cables with special fire performance – Single core non-sheathed cables with halogen-free thermoplastic insulation, and low emission of smoke |
101. |
EN 50525-3-41:2011 Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-41: Cables with special fire performance – Single core non-sheathed cables with halogen-free crosslinked insulation, and low emission of smoke |
102. |
EN 50539-11:2013 Low-voltage surge protective devices – Surge protective devices for specific application including d.c. – Part 11: Requirements and tests for SPDs in photovoltaic applications EN 50539-11:2013/A1:2014 |
103. |
EN 50550:2011 Power frequency overvoltage protective device for household and similar applications (POP) EN 50550:2011/AC:2012 EN 50550:2011/A1:2014 |
104. |
EN 50556:2011 Road traffic signal systems |
105. |
EN 50615:2015 Household and similar electrical appliances – Safety – Particular requirements for devices for fire prevention and suppression for electric hobs (cooktops) |
106. |
EN 50618:2014 Electric cables for photovoltaic systems |
107. |
EN 50620:2017 Electric cables – Charging cables for electric vehicles EN 50620:2017/A1:2019 |
108. |
EN 50689:2021 Safety of laser products – Particular Requirements for Consumer Laser Products |
109. |
EN 60034-1:2010 Rotating electrical machines – Part 1: Rating and performance EN 60034-1:2010/AC:2010 |
110. |
EN 60034-5:2001 Rotating electrical machines – Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification EN 60034-5:2001/A1:2007 |
111. |
EN 60034-6:1993 Rotating electrical machines – Part 6: Methods of cooling (IC Code)#IEC 60034-6:1991 |
112. |
EN 60034-7:1993 Rotating electrical machines – Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code) EN 60034-7:1993/A1:2001 |
113. |
EN 60034-8:2007 Rotating electrical machines – Part 8: Terminal markings and direction of rotation EN 60034-8:2007/A1:2014 |
114. |
EN 60034-9:2005 Rotating electrical machines – Part 9: Noise limits EN 60034-9:2005/A1:2007 |
115. |
EN 60034-11:2004 Rotating electrical machines – Part 11: Thermal protection |
116. |
EN 60034-12:2002 Rotating electrical machines – Part 12: Starting performance of single-speed three-phase cage induction motors EN 60034-12:2002/A1:2007 |
117. |
EN 60034-14:2004 Rotating electrical machines – Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher – Measurement, evaluation and limits of vibration severity EN 60034-14:2004/A1:2007 |
118. |
EN 60051-1:1998 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 1: Definitions and general requirements common to all parts |
119. |
EN 60051-2:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 2: Special requirements for ammeters and voltmeters |
120. |
EN 60051-3:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 3: Special requirements for wattmeters and varmeters EN 60051-3:1989/A1:1995 |
121. |
EN 60051-4:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 4: Special requirements for frequency meters |
122. |
EN 60051-5:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 5: Special requirements for phase meters, power factor meters and synchroscopes |
123. |
EN 60051-6:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters |
124. |
EN 60051-7:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 7: Special requirements for multi-function instruments |
125. |
EN 60051-8:1989 Direct acting indicating analogue electrical measuring instruments and their accessories – Part 8: Special requirements for accessories |
126. |
EN 60051-9:1989 Direct acting indicating analogue electrical-measuring instruments and their accessories – Part 9: Recommended test methods EN 60051-9:1989/A1:1995 EN 60051-9:1989/A2:1995 |
127. |
EN 60110-1:1998 Power capacitors for induction heating installations – Part 1: General |
128. |
EN 60127-1:2006 Miniature fuses – Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links EN 60127-1:2006/A1:2011 EN 60127-1:2006/A2:2015 |
129. |
EN 60127-2:2014 Miniature fuses – Part 2: Cartridge fuse-links |
130. |
EN 60127-3:1996 Miniature fuses – Part 3: Sub-miniature fuse-links EN 60127-3:1996/A2:2003 EN 60127-3:1996/AC:1996 |
131. |
EN 60127-4:2005 Miniature fuses – Part 4: Universal modular fuse-links (UMF) – Through-hole and surface mount types EN 60127-4:2005/A1:2009 EN 60127-4:2005/A2:2013 |
132. |
EN 60127-6:2014 Miniature fuses – Part 6: Fuse-holders for miniature fuse-links |
133. |
EN 60127-7:2016 Miniature fuses – Part 7: Miniature fuse-links for special applications |
134. |
EN 60143-2:2013 Series capacitors for power systems – Part 2: Protective equipment for series capacitor banks |
135. |
EN 60155:1995 Glow-starters for fluorescent lamps EN 60155:1995/A1:1995 EN 60155:1995/A2:2007 |
136. |
EN 60204-1:2018 Safety of machinery – Electrical equipment of machines – Part 1: General requirements |
137. |
EN 60204-32:2008 Safety of machinery – Electrical equipment of machines – Part 32: Requirements for hoisting machines |
138. |
EN 60215:1989 Safety requirements for radio transmitting equipment EN 60215:1989/A1:1992 EN 60215:1989/A2:1994 |
139. |
EN IEC 60238:2018 Edison screw lampholders |
140. |
EN 60252-1:2011 AC motor capacitors – Part 1: General – Performance, testing and rating – Safety requirements – Guidance for installation and operation EN 60252-1:2011/A1:2013 |
141. |
EN 60252-2:2011 AC motor capacitors – Part 2: Motor start capacitors EN 60252-2:2011/A1:2013 |
142. |
EN 60255-27:2014 Measuring relays and protection equipment – Part 27: Product safety requirements |
143. |
EN 60269-1:2007 Low-voltage fuses – Part 1: General requirements EN 60269-1:2007/A1:2009 EN 60269-1:2007/A2:2014 |
144. |
HD 60269-2:2013 Low-voltage fuses – Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to K |
145. |
HD 60269-3:2010 Low-voltage fuses – Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) – Examples of standardized systems of fuses A to F HD 60269-3:2010/A1:2013 |
146. |
EN 60269-4:2009 Low-voltage fuses – Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices EN 60269-4:2009/A1:2012 |
147. |
EN 60269-6:2011 Low-voltage fuses – Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems |
148. |
EN 60309-1:1999 Plugs, socket-outlets and couplers for industrial purposes – Part 1: General requirements EN 60309-1:1999/A1:2007 EN 60309-1:1999/A2:2012 EN 60309-1:1999/A1:2007/AC:2014 |
149. |
EN 60309-2:1999 Plugs, socket-outlets and couplers for industrial purposes – Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories EN 60309-2:1999/A1:2007 EN 60309-2:1999/A2:2012 |
150. |
EN 60309-4:2007 Plugs, socket-outlets and couplers for industrial purposes – Part 4: Switched socket-outlets and connectors with or without interlock EN 60309-4:2007/A1:2012 |
151. |
EN IEC 60320-1:2021 Appliance couplers for household and similar general purposes – Part 1: General requirements |
152. |
EN 60320-2-1:2000 Appliance couplers for household and similar general purposes – Part 2-1: Sewing machine couplers |
153. |
EN 60320-2-2:1998 Appliance couplers for household and similar general purposes – Part 2-2: Interconnection couplers for household and similar equipment |
154. |
EN IEC 60320-2-4:2021 Appliance couplers for household and similar general purposes – Part 2-4: Couplers dependent on appliance weight for engagement |
155. |
EN 60335-1:2012 Household and similar electrical appliances – Safety – Part 1: General requirements EN 60335-1:2012/AC:2014 EN 60335-1:2012/A11:2014 EN 60335-1:2012/A13:2017 EN 60335-1:2012/A1:2019 EN 60335-1:2012/A14:2019 EN 60335-1:2012/A2:2019 EN 60335-1:2012/A15:2021 |
156. |
EN 60335-2-2:2010 Household and similar electrical appliances – Safety – Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances EN 60335-2-2:2010/A11:2012 EN 60335-2-2:2010/A1:2013 |
157. |
EN 60335-2-3:2016 Household and similar electrical appliances – Safety – Part 2-3: Particular requirements for electric irons EN 60335-2-3:2016/A1:2020 |
158. |
EN 60335-2-4:2010 Household and similar electrical appliances – Safety – Part 2-4: Particular requirements for spin extractors EN 60335-2-4:2010/A1:2015 EN 60335-2-4:2010/A11:2018 EN 60335-2-4:2010/A2:2019 |
159. |
EN 60335-2-5:2015 Household and similar electrical appliances – Safety – Part 2-5: Particular requirements for dishwashers EN 60335-2-5:2015/A11:2019 EN 60335-2-5:2015/A1:2020 |
160. |
EN 60335-2-6:2015 Household and similar electrical appliances – Safety – Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances EN 60335-2-6:2015/A11:2020 |
161. |
EN 60335-2-7:2010 Household and similar electrical appliances – Safety – Part 2-7: Particular requirements for washing machines EN 60335-2-7:2010/A11:2013 EN 60335-2-7:2010/A1:2013 EN 60335-2-7:2010/A2:2019 |
162. |
EN 60335-2-8:2015 Household and similar electrical appliances – Safety – Part 2-8: Particular requirements for shavers, hair clippers and similar appliances EN 60335-2-8:2015/A1:2016 |
163. |
EN 60335-2-9:2003 Household and similar electrical appliances – Safety – Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliances EN 60335-2-9:2003/A1:2004 EN 60335-2-9:2003/A12:2007 EN 60335-2-9:2003/A13:2010 EN 60335-2-9:2003/A2:2006 EN 60335-2-9:2003/A13:2010/AC:2011 EN 60335-2-9:2003/A13:2010/AC:2012 Restriction: The application of the following parts of standard EN 60335-2-9:2003, as last amended by A13:2010, does not confer a presumption of conformity to the safety objectives laid down in point 1(c) of Annex I to Directive 2014/35/EU, in conjunction with point 2(b) of that Annex: – footnote b of Table Z101 in Section 11, – the parts of Section 7.1 which refer to footnote b of Table Z101, – the parts of Section 11.Z10x which refer to ventilation openings. |
164. |
EN 60335-2-10:2003 Household and similar electrical appliances – Safety – Part 2-10: Particular requirements for floor treatment machines and wet scrubbing machines EN 60335-2-10:2003/A1:2008 |
165. |
EN IEC 60335-2-11:2022 Household and similar electrical appliances – Safety – Part 2-11: Particular requirements for tumble dryers EN IEC 60335-2-11:2022/A11:2022 |
166. |
EN 60335-2-12:2003 Household and similar electrical appliances – Safety – Part 2-12: Particular requirements for warming plates and similar appliances EN 60335-2-12:2003/A1:2008 EN 60335-2-12:2003/A11:2019 EN 60335-2-12:2003/A2:2019 |
167. |
EN 60335-2-13:2010 Household and similar electrical appliances – Safety – Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances EN 60335-2-13:2010/A11:2012 EN 60335-2-13:2010/A1:2019 |
168. |
EN 60335-2-15:2016 Household and similar electrical appliances – Safety – Part 2-15: Particular requirements for appliances for heating liquids EN 60335-2-15:2016/A11:2018 EN 60335-2-15:2016/A1:2021 EN 60335-2-15:2016/A12:2021 EN 60335-2-15:2016/A2:2021 |
169. |
EN 60335-2-16:2003 Household and similar electrical appliances – Safety – Part 2-16: Particular requirements for food waste disposers EN 60335-2-16:2003/A1:2008 EN 60335-2-16:2003/A2:2012 EN 60335-2-16:2003/A11:2018 |
170. |
EN 60335-2-17:2013 Household and similar electrical appliances – Safety – Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances EN 60335-2-17:2013/A11:2019 EN 60335-2-17:2013/A1:2020 EN 60335-2-17:2013/A2:2021 |
171. |
EN 60335-2-21:2021 Household and similar electrical appliances – Safety – Part 2-21: Particular requirements for storage water heaters EN 60335-2-21:2021/A1:2021 |
172. |
EN 60335-2-23:2003 Household and similar electrical appliances – Safety – Part 2-23: Particular requirements for appliances for skin or hair care EN 60335-2-23:2003/A11:2010/AC:2012 EN 60335-2-23:2003/A11:2010 EN 60335-2-23:2003/A1:2008 EN 60335-2-23:2003/A2:2015 |
173. |
EN IEC 60335-2-24:2022 Household and similar electrical appliances – Safety – Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers EN IEC 60335-2-24:2022/A11:2022 |
174. |
EN IEC 60335-2-25:2021 Household and similar electrical appliances – Safety – Part 2-25: Particular requirements for microwave ovens, including combination microwave ovens EN IEC 60335-2-25:2021/A11:2021 |
175. |
EN 60335-2-26:2003 Household and similar electrical appliances – Safety – Part 2-26: Particular requirements for clocks EN 60335-2-26:2003/A1:2008 |
176. |
EN 60335-2-27:2013 Household and similar electrical appliances – Safety – Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation EN 60335-2-27:2013/A1:2020 EN 60335-2-27:2013/A2:2020 EN 60335-2-27:2013/AC:2021-11 |
177. |
EN 60335-2-28:2003 Household and similar electrical appliances – Safety – Part 2-28: Particular requirements for sewing machines EN 60335-2-28:2003/A1:2008 EN 60335-2-28:2003/A11:2018 |
178. |
EN 60335-2-29:2021 Household and similar electrical appliances – Safety – Part 2-29: Particular requirements for battery chargers EN 60335-2-29:2021/A1:2021 |
179. |
EN 60335-2-30:2009 Household and similar electrical appliances – Safety – Part 2-30: Particular requirements for room heaters EN 60335-2-30:2009/A11:2012 EN 60335-2-30:2009/AC:2010 EN 60335-2-30:2009/AC:2014 EN 60335-2-30:2009/A1:2020 EN 60335-2-30:2009/A12:2020 EN 60335-2-30:2009/A13:2022 EN 60335-2-30:2009/A2:2022 |
180. |
EN 60335-2-31:2014 Household and similar electrical appliances – Safety – Part 2-31: Particular requirements for range hoods and other cooking fume extractors |
181. |
EN 60335-2-32:2003 Household and similar electrical appliances – Safety – Part 2-32: Particular requirements for massage appliances EN 60335-2-32:2003/A1:2008 EN 60335-2-32:2003/A2:2015 |
182. |
EN 60335-2-34:2013 Household and similar electrical appliances – Safety – Part 2-34: Particular requirements for motor-compressors |
183. |
EN 60335-2-35:2016 Household and similar electrical appliances – Safety – Part 2-35: Particular requirements for instantaneous water heaters EN 60335-2-35:2016/A1:2019 EN 60335-2-35:2016/A2:2021 |
184. |
EN 60335-2-36:2002 Household and similar electrical appliances – Safety – Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements EN 60335-2-36:2002/A1:2004 EN 60335-2-36:2002/A11:2012 EN 60335-2-36:2002/A2:2008 EN 60335-2-36:2002/AC:2007 |
185. |
EN 60335-2-37:2002 Household and similar electrical appliances – Safety – Part 2-37: Particular requirements for commercial electric deep fat fryers EN 60335-2-37:2002/A1:2008 EN 60335-2-37:2002/A11:2012 EN 60335-2-37:2002/AC:2007 |
186. |
EN 60335-2-38:2003 Household and similar electrical appliances – Safety – Part 2-38: Particular requirements for commercial electric griddles and griddle grills EN 60335-2-38:2003/A1:2008 EN 60335-2-38:2003/AC:2007 |
187. |
EN 60335-2-39:2003 Household and similar electrical appliances – Safety – Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans EN 60335-2-39:2003/A1:2004 EN 60335-2-39:2003/A2:2008 EN 60335-2-39:2003/AC:2007 |
188. |
EN 60335-2-40:2003 Household and similar electrical appliances – Safety – Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers EN 60335-2-40:2003/A11:2004 EN 60335-2-40:2003/A12:2005 EN 60335-2-40:2003/A1:2006 EN 60335-2-40:2003/A13:2012/AC:2013 EN 60335-2-40:2003/A13:2012 EN 60335-2-40:2003/A2:2009 EN 60335-2-40:2003/AC:2006 EN 60335-2-40:2003/AC:2010 |
189. |
EN IEC 60335-2-41:2021 Household and similar electrical appliances – Safety – Particular requirements for pumps EN IEC 60335-2-41:2021/A11:2021 |
190. |
EN 60335-2-42:2003 Household and similar electrical appliances – Safety – Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens EN 60335-2-42:2003/A1:2008 EN 60335-2-42:2003/A11:2012 EN 60335-2-42:2003/AC:2007 |
191. |
EN IEC 60335-2-43:2020 Household and similar electrical appliances – Safety – Part 2-43: Particular requirements for clothes dryers and towel rails EN IEC 60335-2-43:2020/A11:2020 |
192. |
EN 60335-2-44:2002 Household and similar electrical appliances – Safety – Part 2-44: Particular requirements for ironers EN 60335-2-44:2002/A1:2008 EN 60335-2-44:2002/A2:2012 |
193. |
EN 60335-2-45:2002 Household and similar electrical appliances – Safety – Part 2-45: Particular requirements for portable heating tools and similar appliances EN 60335-2-45:2002/A1:2008 EN 60335-2-45:2002/A2:2012 |
194. |
EN 60335-2-47:2003 Household and similar electrical appliances – Safety – Part 2-47: Particular requirements for commercial electric boiling pans EN 60335-2-47:2003/A1:2008 EN 60335-2-47:2003/A11:2012 EN 60335-2-47:2003/AC:2007 EN 60335-2-47:2003/A2:2019 |
195. |
EN 60335-2-48:2003 Household and similar electrical appliances – Safety – Part 2-48: Particular requirements for commercial electric grillers and toasters EN 60335-2-48:2003/A1:2008 EN 60335-2-48:2003/A11:2012 EN 60335-2-48:2003/AC:2007 EN 60335-2-48:2003/A2:2019 |
196. |
EN 60335-2-49:2003 Household and similar electrical appliances – Safety – Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm EN 60335-2-49:2003/A1:2008 EN 60335-2-49:2003/A11:2012 EN 60335-2-49:2003/AC:2007 EN 60335-2-49:2003/A2:2019 |
197. |
EN 60335-2-50:2003 Household and similar electrical appliances – Safety – Part 2-50: Particular requirements for commercial electric bains-marie EN 60335-2-50:2003/A1:2008 EN 60335-2-50:2003/AC:2007 |
198. |
EN 60335-2-51:2003 Household and similar electrical appliances – Safety – Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations EN 60335-2-51:2003/A1:2008 EN 60335-2-51:2003/A2:2012 |
199. |
EN 60335-2-52:2003 Household and similar electrical appliances – Safety – Part 2-52: Particular requirements for oral hygiene appliances EN 60335-2-52:2003/A11:2010/AC:2012 EN 60335-2-52:2003/A11:2010 EN 60335-2-52:2003/A1:2008 EN 60335-2-52:2003/A12:2019 |
200. |
EN 60335-2-53:2011 Household and similar electrical appliances – Safety – Part 2-53: Particular requirements for sauna heating appliances and infrared cabins |
201. |
EN 60335-2-54:2008 Household and similar electrical appliances – Safety – Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam EN 60335-2-54:2008/A11:2012/AC:2015 EN 60335-2-54:2008/A11:2012 EN 60335-2-54:2008/A1:2015 EN 60335-2-54:2008/A12:2021 EN 60335-2-54:2008/A2:2021 |
202. |
EN 60335-2-55:2003 Household and similar electrical appliances – Safety – Part 2-55: Particular requirements for electrical appliances for use with aquariums and garden ponds EN 60335-2-55:2003/A1:2008 EN 60335-2-55:2003/A11:2018 |
203. |
EN 60335-2-56:2003 Household and similar electrical appliances – Safety – Part 2-56: Particular requirements for projectors and similar appliances EN 60335-2-56:2003/A1:2008 EN 60335-2-56:2003/A2:2014 |
204. |
EN 60335-2-58:2005 Household and similar electrical appliances – Safety – Part 2-58: Particular requirements for commercial electric dishwashing machines |
205. |
EN 60335-2-59:2003 Household and similar electrical appliances – Safety – Part 2-59: Particular requirements for insect killers EN 60335-2-59:2003/A1:2006 EN 60335-2-59:2003/A2:2009 EN 60335-2-59:2003/A11:2018 |
206. |
EN 60335-2-60:2003 Household and similar electrical appliances – Safety – Part 2-60: Particular requirements for whirlpool baths and whirlpool spas EN 60335-2-60:2003/A1:2005 EN 60335-2-60:2003/A12:2010 EN 60335-2-60:2003/A11:2010 EN 60335-2-60:2003/A2:2008 |
207. |
EN 60335-2-61:2003 Household and similar electrical appliances – Safety – Part 2-61: Particular requirements for thermal-storage room heaters EN 60335-2-61:2003/A1:2005 EN 60335-2-61:2003/A2:2008 EN 60335-2-61:2003/A11:2019 EN 60335-2-61:2003/A12:2021 |
208. |
EN 60335-2-62:2003 Household and similar electrical appliances – Safety – Part 2-62: Particular requirements for commercial electric rinsing sinks EN 60335-2-62:2003/A1:2008 EN 60335-2-62:2003/AC:2007 |
209. |
EN 60335-2-65:2003 Household and similar electrical appliances – Safety – Part 2-65: Particular requirements for air-cleaning appliances EN 60335-2-65:2003/A1:2008 EN 60335-2-65:2003/A11:2012 |
210. |
EN 60335-2-66:2003 Household and similar electrical appliances – Safety – Part 2-66: Particular requirements for water-bed heaters EN 60335-2-66:2003/A1:2008 EN 60335-2-66:2003/A2:2012 EN 60335-2-66:2003/A11:2019 |
211. |
EN 60335-2-70:2002 Household and similar electrical appliances – Safety – Part 2-70: Particular requirements for milking machines |
212. |
EN 60335-2-71:2003 Household and similar electrical appliances – Safety – Part 2-71: Particular requirements for electrical heating appliances for breeding and rearing animals EN 60335-2-71:2003/A1:2007 |
213. |
EN 60335-2-73:2003 Household and similar electrical appliances – Safety – Part 2-73: Particular requirements for fixed immersion heaters EN 60335-2-73:2003/A1:2006 EN 60335-2-73:2003/A2:2009 EN 60335-2-73:2003/A11:2021 |
214. |
EN 60335-2-74:2003 Household and similar electrical appliances – Safety – Part 2-74: Particular requirements for portable immersion heaters EN 60335-2-74:2003/A1:2006 EN 60335-2-74:2003/A2:2009 EN 60335-2-74:2003/A11:2018 |
215. |
EN 60335-2-75:2004 Household and similar electrical appliances – Safety – Part 2-75: Particular requirements for commercial dispensing appliances and vending machines EN 60335-2-75:2004/A11:2006 EN 60335-2-75:2004/A1:2005 EN 60335-2-75:2004/A12:2010 EN 60335-2-75:2004/A2:2008 |
216. |
EN 60335-2-78:2003 Household and similar electrical appliances – Safety – Part 2-78: Particular requirements for outdoor barbecues EN 60335-2-78:2003/A1:2008 EN 60335-2-78:2003/A11:2020 |
217. |
EN 60335-2-80:2003 +6Household and similar electrical appliances – Safety – Part 2-80: Particular requirements for fans EN 60335-2-80:2003/A1:2004 EN 60335-2-80:2003/A2:2009 |
218. |
EN 60335-2-81:2003 Household and similar electrical appliances – Safety – Part 2-81: Particular requirements for foot warmers and heating mats EN 60335-2-81:2003/A1:2007 EN 60335-2-81:2003/A2:2012 |
219. |
EN 60335-2-82:2003 Household and similar electrical appliances – Safety – Part 2-82: Particular requirements for amusement machines and personal service machines EN 60335-2-82:2003/A1:2008 EN 60335-2-82:2003/A2:2020 |
220. |
EN 60335-2-83:2002 Household and similar electrical appliances – Safety – Part 2-83: Particular requirements for heated gullies for roof drainage EN 60335-2-83:2002/A1:2008 |
221. |
EN IEC 60335-2-84:2021 Household and similar electrical appliances – Safety – Part 2-84: Particular requirements for toilet appliances EN IEC 60335-2-84:2021/A11:2021 |
222. |
EN 60335-2-85:2003 Household and similar electrical appliances – Safety – Part 2-85: Particular requirements for fabric steamers EN 60335-2-85:2003/A1:2008 EN 60335-2-85:2003/A11:2018 EN 60335-2-85:2003/A2:2020 |
223. |
EN 60335-2-86:2003 Household and similar electrical appliances – Safety – Part 2-86: Particular requirements for electric fishing machines EN 60335-2-86:2003/A1:2005 EN 60335-2-86:2003/A11:2016 EN 60335-2-86:2003/A2:2016 |
224. |
EN 60335-2-87:2002 Household and similar electrical appliances – Safety – Part 2-87: Particular requirements for electrical animal-stunning equipment EN 60335-2-87:2002/A1:2007 EN 60335-2-87:2002/A2:2019 |
225. |
EN 60335-2-88:2002 Household and similar electrical appliances – Safety – Part 2-88: Particular requirements for humidifiers intended for use with heating, ventilation, or air-conditioning systems |
226. |
EN 60335-2-90:2006 Household and similar electrical appliances – Safety – Part 2-90: Particular requirements for commercial microwave ovens EN 60335-2-90:2006/A1:2010 |
227. |
EN IEC 60335-2-96:2021 Household and similar electrical appliances – Safety – Part 2-96: Particular requirements for flexible sheet heating elements for room heating EN IEC 60335-2-96:2021/A11:2021 |
228. |
EN 60335-2-97:2006 Household and similar electrical appliances – Safety – Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment EN 60335-2-97:2006/A11:2008 EN 60335-2-97:2006/A12:2015 EN 60335-2-97:2006/A2:2010 |
229. |
EN 60335-2-98:2003 Household and similar electrical appliances – Safety – Part 2-98: Particular requirements for humidifiers EN 60335-2-98:2003/A1:2005 EN 60335-2-98:2003/A2:2008 EN 60335-2-98:2003/A11:2019 |
230. |
EN 60335-2-99:2003 Household and similar electrical appliances – Safety – Part 2-99: Particular requirements for commercial electric hoods |
231. |
EN 60335-2-101:2002 Household and similar electrical appliances – Safety – Part 2-101: Particular requirements for vaporizers EN 60335-2-101:2002/A1:2008 EN 60335-2-101:2002/A2:2014 |
232. |
EN 60335-2-102:2016 Household and similar electrical appliances – Safety – Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
233. |
EN IEC 60335-2-105:2021 Household and similar electrical appliances – Safety – Part 2-105: Particular requirements for multifunctional shower cabinets EN IEC 60335-2-105:2021/A11:2021 |
234. |
EN 60335-2-106:2007 Household and similar electrical appliances – Safety – Part 2-106: Particular requirements for heated carpets and for heating units for room heating installed under removable floor coverings |
235. |
EN 60335-2-108:2008 Household and similar electrical appliances – Safety – Part 2-108: Particular requirements for electrolysers |
236. |
EN 60335-2-109:2010 Household and similar electrical appliances – Safety – Part 2-109: Particular requirements for UV radiation water treatment appliances EN 60335-2-109:2010/A1:2018 EN 60335-2-109:2010/A2:2018 |
237. |
EN 60358-1:2012 Coupling capacitors and capacitor dividers – Part 1: General rules EN 60358-1:2012/AC:2013 |
238. |
EN 60360:1998 Standard method of measurement of lamp cap temperature rise |
239. |
EN 60399:2004 Barrel thread for lampholders with shade holder ring EN 60399:2004/A1:2008 |
240. |
EN 60400:2017 Lampholders for tubular fluorescent lamps and starterholders EN 60400:2017/A1:2021 |
241. |
EN 60423:2007 Conduit systems for cable management – Outside diameters of conduits for electrical installations and threads for conduits and fittings |
242. |
EN 60432-1:2000 Incandescent lamps – Safety specifications – Part 1: Tungsten filament lamps for domestic and similar general lighting purposes EN 60432-1:2000/A1:2005 EN 60432-1:2000/A2:2012 |
243. |
EN 60432-2:2000 Incandescent lamps – Safety specifications – Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes EN 60432-2:2000/A1:2005 EN 60432-2:2000/A2:2012 |
244. |
EN 60432-3:2013 Incandescent lamps – Safety specifications – Part 3: Tungsten-halogen lamps (non-vehicle) |
245. |
EN 60477:1997 Laboratory d.c. resistors EN 60477:1997/A1:1997 |
246. |
EN 60477-2:1997 Laboratory resistors – Part 2: Laboratory a.c. resistors EN 60477-2:1997/A1:1997 |
247. |
EN 60519-1:2015 Safety in installations for electroheating and electromagnetic processing – Part 1: General requirements |
248. |
EN 60519-2:2006 Safety in electroheat installations – Part 2: Particular requirements for resistance heating equipment |
249. |
EN 60519-3:2005 Safety in electroheat installations – Part 3: Particular requirements for induction and conduction heating and induction melting installations |
250. |
EN 60519-4:2013 Safety in electroheating installations – Part 4: Particular requirements for arc furnace installations |
251. |
EN 60519-6:2011 Safety in electroheat installations – Part 6: Specifications for safety in industrial microwave heating equipment |
252. |
EN 60519-7:2008 Safety in electroheat installations – Part 7: Particular requirements for installations with electron guns |
253. |
EN 60519-8:2005 Safety in electroheat installations – Part 8: Particular requirements for electroslag remelting furnaces |
254. |
EN 60519-9:2005 Safety in electroheat installations – Part 9: Particular requirements for high-frequency dielectric heating installations |
255. |
EN 60519-10:2013 Safety in electroheating installations – Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications |
256. |
EN 60519-12:2013 Safety in electroheating installations – Part 12: Particular requirements for infrared electroheating installations |
257. |
EN 60519-21:2009 Safety in electroheat installations – Part 21: Particular requirements for resistance heating equipment – Heating and melting glass equipment#IEC 60519-21:2008 |
258. |
EN 60523:1993 Direct-current potentiometers EN 60523:1993/A2:1997 |
259. |
EN 60524:1993 Direct-current resistive volt ratio boxes EN 60524:1993/A2:1997 |
260. |
EN 60529:1991 Degrees of protection provided by enclosures (IP Code)#IEC 60529:1989 EN 60529:1991/A1:2000 EN 60529:1991/A2:2013 EN 60529:1991/AC:1993 EN 60529:1991/AC:2016-12 EN 60529:1991/A2:2013/AC:2019-02 |
261. |
EN 60564:1993 D.C. bridges for measuring resistance EN 60564:1993/A2:1997 |
262. |
EN 60570:2003 Electrical supply track systems for luminaires EN 60570:2003/A1:2018 EN 60570:2003/A2:2020 |
263. |
EN IEC 60598-1:2021 Luminaires – Part 1: General requirements and tests EN IEC 60598-1:2021/A11:2022 |
264. |
EN 60598-2-1:1989 Luminaires – Part 2: Particular requirements – Section 1: Fixed general purpose luminaires |
265. |
EN 60598-2-2:2012 Luminaires – Part 2-2: Particular requirements – Recessed luminaires |
266. |
EN 60598-2-3:2003 Luminaires – Part 2-3: Particular requirements – Luminaires for road and street lighting EN 60598-2-3:2003/A1:2011 EN 60598-2-3:2003/AC:2005 |
267. |
EN 60598-2-4:2018 Luminaires – Part 2: Particular requirements – Section 4: Portable general purpose luminaires |
268. |
EN 60598-2-5:2015 Luminaires – Part 2-5: Particular requirements – Floodlights |
269. |
EN 60598-2-8:2013 Luminaires – Part 2-8: Particular requirements – Handlamps |
270. |
EN 60598-2-9:1989 Luminaires – Part 2: Particular requirements – Section 9: Photo and film luminaires (non-professional) EN 60598-2-9:1989/A1:1994 |
271. |
EN 60598-2-10:2003 Luminaires – Part 2-10: Particular requirements – Portable luminaires for children EN 60598-2-10:2003/AC:2005 |
272. |
EN 60598-2-11:2013 Luminaires – Part 2-11: Particular requirements – Aquarium luminaires EN 60598-2-11:2013/A1:2022 |
273. |
EN 60598-2-12:2013 Luminaires – Part 2-12: Particular requirements – Mains socket-outlet mounted nightlights |
274. |
EN 60598-2-13:2006 Luminaires – Part 2-13: Particular requirements – Ground recessed luminaires EN 60598-2-13:2006/A1:2012 EN 60598-2-13:2006/AC:2006 EN 60598-2-13:2006/A11:2021 |
275. |
EN 60598-2-14:2009 Luminaires – Part 2-14: Particular requirements – Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment |
276. |
EN IEC 60598-2-17:2018 Luminaires – Part 2-17: Particular requirements – Luminaires for stage lighting, television and film studios (outdoor and indoor) |
277. |
EN 60598-2-19:1989 Luminaires – Part 2: Particular requirements – Section 19: Air-handling luminaires (safety requirements) EN 60598-2-19:1989/A2:1998 EN 60598-2-19:1989/AC:2005 |
278. |
EN 60598-2-20:2015 Luminaires – Part 2-20: Particular requirements – Lighting chains EN 60598-2-20:2015/AC:2017-01 |
279. |
EN 60598-2-21:2015 Luminaires – Part 2-21: Particular requirements – Rope lights EN 60598-2-21:2015/AC:2017-01 |
280. |
EN IEC 60598-2-22:2022 Luminaires – Part 2-22: Particular requirements – Luminaires for emergency lighting |
281. |
EN IEC 60598-2-23:2021 Luminaires – Part 2-23: Particular requirements – Extra-low-voltage lighting systems for ELV light sources |
282. |
EN 60598-2-24:2013 Luminaires – Part 2-24: Particular requirements – Luminaires with limited surface temperatures |
283. |
EN 60598-2-25:1994 Luminaires – Part 2-25: Particular requirements – Luminaires for use in clinical areas of hospitals and health care buildings EN 60598-2-25:1994/A1:2004 |
284. |
EN 60618:1997 Inductive voltage dividers EN 60618:1997/A2:1997 |
285. |
EN 60645-1:2015 Electroacoustics – Audiometric equipment – Part 1: Equipment for pure-tone audiometry |
286. |
EN 60645-3:2007 Electroacoustics – Audiometric equipment – Part 3: Test signals of short duration |
287. |
EN 60645-6:2010 Electroacoustics – Audiometric equipment – Part 6: Instruments for the measurement of otoacoustic emissions |
288. |
EN 60645-7:2010 Electroacoustics – Audiometric equipment – Part 7: Instruments for the measurement of auditory brainstem responses |
289. |
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems – Part 1: Principles, requirements and tests |
290. |
EN 60664-3:2003 Insulation coordination for equipment within low-voltage systems – Part 3: Use of coating, potting or moulding for protection against pollution EN 60664-3:2003/A1:2010 |
291. |
EN 60664-4:2006 Insulation coordination for equipment within low-voltage systems – Part 4: Consideration of high-frequency voltage stress EN 60664-4:2006/AC:2006 |
292. |
EN 60669-1:2018 Switches for household and similar fixed electrical installations – Part 1: General requirements EN 60669-1:2018/AC:2018-11 EN 60669-1:2018/AC:2020-02 |
293. |
EN 60669-2-1:2004 Switches for household and similar fixed electrical installations – Part 2-1: Particular requirements – Electronic switches EN 60669-2-1:2004/A1:2009 EN 60669-2-1:2004/A12:2010 EN 60669-2-1:2004/AC:2007 |
294. |
EN 60669-2-2:2006 Switches for household and similar fixed electrical installations – Part 2-2: Particular requirements – Electromagnetic remote-control switches (RCS) |
295. |
EN 60669-2-3:2006 Switches for household and similar fixed electrical installations – Part 2-3: Particular requirements – Time delay switches (TDS) |
296. |
EN 60669-2-4:2005 Switches for household and similar fixed electrical installations – Part 2-4: Particular requirements – Isolating switches |
297. |
EN 60669-2-6:2012 Switches for household and similar fixed electrical installations – Part 2-6: Particular requirements – Fireman’s switches for exterior and interior signs and luminaires |
298. |
EN IEC 60670-1:2021 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 1: General requirements EN IEC 60670-1:2021/A11:2021 |
299. |
EN 60670-21:2007 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 21: Particular requirements for boxes and enclosures with provision for suspension means |
300. |
EN 60670-22:2006 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 22: Particular requirements for connecting boxes and enclosures |
301. |
EN 60670-23:2008 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 23: Particular requirements for floor boxes and enclosures |
302. |
EN 60670-24:2013 Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment |
303. |
EN 60688:2013 Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
304. |
EN 60691:2016 Thermal-links – Requirements and application guide EN 60691:2016/A1:2019 |
305. |
EN 60695-2-10:2013 Fire hazard testing – Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and common test procedure |
306. |
EN 60695-2-11:2014 Fire hazard testing – Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014) |
307. |
EN 60695-10-2:2014 Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method |
308. |
EN 60695-10-3:2002 Fire hazard testing – Part 10-3: Abnormal heat – Mould stress relief distortion test |
309. |
EN 60695-11-2:2014 Fire hazard testing – Part 11-2: Test flames – 1 kW nominal pre-mixed flame: Apparatus, confirmatory test arrangement and guidance |
310. |
EN 60695-11-3:2012 Fire hazard testing – Part 11-3: Test flames – 500 W flames – Apparatus and confirmational test methods |
311. |
EN 60695-11-4:2011 Fire hazard testing – Part 11-4: Test flames – 50 W flame – Apparatus and confirmational test method |
312. |
EN 60695-11-5:2005 Fire hazard testing – Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test arrangement and guidance |
313. |
EN 60695-11-10:2013 Fire hazard testing – Part 11-10: Test flames – 50 W horizontal and vertical flame test methods EN 60695-11-10:2013/AC:2014 |
314. |
EN 60695-11-20:2015 Fire hazard testing – Part 11-20: Test flames – 500 W flame test method EN 60695-11-20:2015/AC:2016 |
315. |
EN 60702-1:2002 Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V – Part 1: Cables EN 60702-1:2002/A1:2015 |
316. |
EN 60702-2:2002 Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V – Part 2: Terminations EN 60702-2:2002/A1:2015 |
317. |
EN 60715:2017 Dimensions of low-voltage switchgear and controlgear – Standardized mounting on rails for mechanical support of switchgear, controlgear and accessories |
318. |
EN 60719:1993 Calculation of the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750 V |
319. |
EN 60728-11:2017 Cable networks for television signals, sound signals and interactive services – Part 11: Safety EN 60728-11:2017/A11:2018 |
320. |
EN 60730-1:2011 Automatic electrical controls for household and similar use – Part 1: General requirements |
321. |
EN 60730-2-2:2002 Automatic electrical controls for household and similar use – Part 2-2: Particular requirements for thermal motor protectors EN 60730-2-2:2002/A11:2005 |
322. |
EN 60730-2-3:2007 Automatic electrical controls for household and similar use – Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps |
323. |
EN 60730-2-4:2007 Automatic electrical controls for household and similar use – Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type |
324. |
EN 60730-2-5:2015 Automatic electrical controls – Part 2-5: Particular requirements for automatic electrical burner control systems |
325. |
EN 60730-2-6:2016 Automatic electrical controls – Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
326. |
EN 60730-2-7:2010 Automatic electrical controls for household and similar use – Part 2-7: Particular requirements for timers and time switches EN 60730-2-7:2010/AC:2011 |
327. |
EN 60730-2-8:2002 Automatic electrical controls for household and similar use – Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements EN 60730-2-8:2002/A1:2003 |
328. |
EN 60730-2-9:2010 Automatic electrical controls for household and similar use – Part 2-9: Particular requirements for temperature sensing controls |
329. |
EN 60730-2-10:2007 Automatic electrical controls for household and similar use – Part 2-10: Particular requirements for motor-starting relays |
330. |
EN 60730-2-11:2008 Automatic electrical controls for household and similar use – Part 2-11: Particular requirements for energy regulators |
331. |
EN 60730-2-12:2006 Automatic electrical controls for household and similar use – Part 2-12: Particular requirements for electrically operated door locks EN 60730-2-12:2006/A11:2008 |
332. |
EN 60730-2-13:2008 Automatic electrical controls for household and similar use – Part 2-13: Particular requirements for humidity sensing controls |
333. |
EN 60730-2-14:1997 Automatic electrical controls for household and similar use – Part 2-14: Particular requirements for electric actuators EN 60730-2-14:1997/A11:2005 EN 60730-2-14:1997/A1:2001 EN 60730-2-14:1997/A2:2008 |
334. |
EN 60730-2-15:2010 Automatic electrical controls for household and similar use – Part 2-15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls |
335. |
EN 60730-2-19:2002 Automatic electrical controls for household and similar use – Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements EN 60730-2-19:2002/A11:2005 EN 60730-2-19:2002/A2:2008 |
336. |
EN 60799:1998 Electrical accessories – Cord sets and interconnection cord sets |
337. |
EN 60825-1:2014 Safety of laser products – Part 1: Equipment classification and requirements EN 60825-1:2014/A11:2021 |
338. |
EN 60825-2:2004 Safety of laser products – Part 2: Safety of optical fibre communication systems (OFCS) EN 60825-2:2004/A1:2007 EN 60825-2:2004/A2:2010 |
339. |
EN 60825-4:2006 Safety of laser products – Part 4: Laser guards EN 60825-4:2006/A1:2008 EN 60825-4:2006/A2:2011 |
340. |
EN 60825-12:2004 Safety of laser products – Part 12: Safety of free space optical communication systems used for transmission of information |
341. |
EN 60831-1:2014 Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V – Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation EN 60831-1:2014/AC:2014 |
342. |
EN 60831-2:2014 Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V – Part 2: Ageing test, self-healing test and destruction test |
343. |
EN 60838-1:2017 Miscellaneous lampholders – Part 1: General requirements and tests EN 60838-1:2017/A1:2017 EN 60838-1:2017/A11:2021 EN 60838-1:2017/A2:2021 |
344. |
EN 60838-2-1:1996 Miscellaneous lampholders – Part 2: Particular requirements – Section 1: Lampholders S14 EN 60838-2-1:1996/A1:1998 EN 60838-2-1:1996/A2:2004 |
345. |
EN 60838-2-2:2006 Miscellaneous lampholders – Part 2-2: Particular requirements – Connectors for LED-modules EN 60838-2-2:2006/A1:2012 |
346. |
EN 60898-1:2019 Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations – Part 1: Circuit-breakers for a.c. operation |
347. |
EN 60898-2:2021 Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations – Part 2: Circuit-breakers for a.c. and d.c. operation |
348. |
EN 60931-1:1996 Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation EN 60931-1:1996/A1:2003 |
349. |
EN 60931-2:1996 Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 2: Ageing test and destruction test |
350. |
EN 60931-3:1996 Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 3: Internal fuses |
351. |
EN IEC 60934:2019 Circuit breakers for equipment (CBE) |
352. |
EN 60947-1:2007 Low-voltage switchgear and controlgear – Part 1: General rules EN 60947-1:2007/A1:2011 EN 60947-1:2007/A2:2014 |
353. |
EN 60947-2:2017 Low-voltage switchgear and controlgear – Part 2: Circuit-breakers EN 60947-2:2017/A1:2020 |
354. |
EN IEC 60947-3:2021 Low-voltage switchgear and controlgear – Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units |
355. |
EN IEC 60947-4-1:2019 Low-voltage switchgear and controlgear – Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters EN IEC 60947-4-1:2019/AC:2020-05 |
356. |
EN 60947-4-2:2012 Low-voltage switchgear and controlgear – Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters |
357. |
EN 60947-4-3:2014 Low-voltage switchgear and controlgear – Part 4-3: Contactors and motor-starters – AC semiconductor controllers and contactors for non-motor loads |
358. |
EN 60947-5-1:2017 Low-voltage switchgear and controlgear – Part 5-1: Control circuit devices and switching elements – Electromechanical control circuit devices EN 60947-5-1:2017/AC:2020-05 |
359. |
EN IEC 60947-5-2:2020 Low-voltage switchgear and controlgear – Part 5-2: Control circuit devices and switching elements – Proximity switches |
360. |
EN 60947-5-3:1999 Low-voltage switchgear and controlgear – Part 5-3: Control circuit devices and switching elements – Requirements for proximity devices with defined behaviour under fault conditions (PDF) EN 60947-5-3:1999/A1:2005 |
361. |
EN 60947-5-4:2003 Low-voltage switchgear and controlgear – Part 5-4: Control circuit devices and switching elements – Method of assessing the performance of low-energy contacts – Special tests EN 60947-5-4:2003/A1:2019 |
362. |
EN 60947-5-5:1997 Low-voltage switchgear and controlgear – Part 5-5: Control circuit devices and switching elements – Electrical emergency stop device with mechanical latching function EN 60947-5-5:1997/A1:2005 EN 60947-5-5:1997/A11:2013 EN 60947-5-5:1997/A2:2017 |
363. |
EN 60947-5-7:2003 Low-voltage switchgear and controlgear – Part 5-7: Control circuit devices and switching elements – Requirements for proximity devices with analogue output |
364. |
EN IEC 60947-5-8:2021 Low-voltage switchgear and controlgear – Part 5-8: Control circuit devices and switching elements – Three-position enabling switches |
365. |
EN 60947-5-9:2007 Low-voltage switchgear and controlgear – Part 5-9: Control circuit devices and switching elements – Flow rate switches |
366. |
EN 60947-6-1:2005 Low-voltage switchgear and controlgear – Part 6-1: Multiple function equipment – Transfer switching equipment EN 60947-6-1:2005/A1:2014 |
367. |
EN 60947-6-2:2003 Low-voltage switchgear and controlgear – Part 6-2: Multiple function equipment – Control and protective switching devices (or equipment) (CPS) EN 60947-6-2:2003/A1:2007 |
368. |
EN 60947-7-1:2009 Low-voltage switchgear and controlgear – Part 7-1: Ancillary equipment – Terminal blocks for copper conductors |
369. |
EN 60947-7-2:2009 Low-voltage switchgear and controlgear – Part 7-2: Ancillary equipment – Protective conductor terminal blocks for copper conductors |
370. |
EN 60947-7-3:2009 Low-voltage switchgear and controlgear – Part 7-3: Ancillary equipment – Safety requirements for fuse terminal blocks |
371. |
EN 60947-8:2003 Low-voltage switchgear and controlgear – Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines EN 60947-8:2003/A1:2006 EN 60947-8:2003/A2:2012 |
372. |
EN IEC 60947-9-1:2019 Low-voltage switchgear and controlgear – Part 9-1: Active arc-fault mitigation systems – Arc quenching devices |
373. |
EN 60950-21:2003 Information technology equipment – Safety – Part 21: Remote power feeding |
374. |
EN 60950-22:2006 Information technology equipment – Safety – Part 22: Equipment installed outdoors EN 60950-22:2006/AC:2008 |
375. |
EN 60950-23:2006 Information technology equipment – Safety – Part 23: Large data storage equipment EN 60950-23:2006/AC:2008 |
376. |
EN 60968:2015 Self-ballasted fluorescent lamps for general lighting services – Safety requirements |
377. |
EN IEC 60974-1:2018 Arc welding equipment – Part 1: Welding power sources EN IEC 60974-1:2018/A1:2019 |
378. |
EN IEC 60974-2:2019 Arc welding equipment – Part 2: Liquid cooling systems |
379. |
EN IEC 60974-3:2019 Arc welding equipment – Part 3: Arc striking and stabilizing devices |
380. |
EN IEC 60974-5:2019 Arc welding equipment – Part 5: Wire feeders |
381. |
EN 60974-6:2016 Arc welding equipment – Part 6: Limited duty equipment |
382. |
EN IEC 60974-7:2019 Arc welding equipment – Part 7: Torches |
383. |
EN IEC 60974-8:2021 Arc welding equipment – Part 8: Gas consoles for welding and plasma cutting systems |
384. |
EN IEC 60974-11:2021 Arc welding equipment – Part 11: Electrode holders |
385. |
EN 60974-12:2011 Arc welding equipment – Part 12: Coupling devices for welding cables |
386. |
EN IEC 60974-13:2021 Arc welding equipment – Part 13: Welding current return clamp |
387. |
EN 60998-1:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 1: General requirements |
388. |
EN 60998-2-1:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units |
389. |
EN 60998-2-2:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units |
390. |
EN 60998-2-3:2004 Connecting devices for low-voltage circuits for household and similar purposes – Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units |
391. |
EN 60998-2-4:2005 Connecting devices for low voltage circuits for household and similar purposes – Part 2-4: Particular requirements for twist-on connecting devices |
392. |
EN 60999-1:2000 Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
393. |
EN 60999-2:2003 Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included) |
394. |
EN 61008-1:2012 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) – Part 1: General rules EN 61008-1:2012/A1:2014 EN 61008-1:2012/A11:2015 EN 61008-1:2012/A2:2014 EN 61008-1:2012/A1:2014/AC:2016-06 EN 61008-1:2012/A12:2017 |
395. |
EN 61008-2-1:1994 Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) – Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage EN 61008-2-1:1994/A11:1998 EN 61008-2-1:1994/A11:1998/AC:1999 |
396. |
EN 61009-1:2012 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) – Part 1: General rules EN 61009-1:2012/A1:2014 EN 61009-1:2012/A11:2015 EN 61009-1:2012/A2:2014 EN 61009-1:2012/A13:2021 |
397. |
EN 61009-2-1:1994 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) – Part 2-1: Applicability of the general rules to RCBO’s functionally independent of line voltage EN 61009-2-1:1994/A11:1998 EN 61009-2-1:1994/A11:1998/AC:1999 |
398. |
EN 61010-1:2010 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 1: General requirements EN 61010-1:2010/A1:2019/AC:2019-04 EN 61010-1:2010/A1:2019 |
399. |
EN IEC 61010-2-010:2020 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-010: Particular requirements for laboratory equipment for the heating of materials |
400. |
EN IEC 61010-2-011:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-011: Particular requirements for refrigerating equipment EN IEC 61010-2-011:2021/A11:2021 |
401. |
EN IEC 61010-2-012:2022 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-012: Particular requirements for climatic and environmental testing and other temperature conditioning equipment EN IEC 61010-2-012:2022/A11:2022 |
402. |
EN 61010-2-020:2006 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-020: Particular requirements for laboratory centrifuges |
403. |
EN IEC 61010-2-030:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-030: Particular requirements for equipment having testing or measuring circuits EN IEC 61010-2-030:2021/A11:2021 |
404. |
EN IEC 61010-2-032:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement EN IEC 61010-2-032:2021/A11:2021 |
405. |
EN IEC 61010-2-033:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-033: Particular requirements for hand-held multimeters for domestic and professional use, capable of measuring mains voltage EN IEC 61010-2-033:2021/A11:2021 |
406. |
EN IEC 61010-2-034:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-034: Particular requirements for measurement equipment for insulation resistance and test equipment for electric strength EN IEC 61010-2-034:2021/A11:2021 |
407. |
EN IEC 61010-2-040:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials |
408. |
EN IEC 61010-2-051:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-051: Particular requirements for laboratory equipment for mixing and stirring EN IEC 61010-2-051:2021/A11:2021 |
409. |
EN IEC 61010-2-061:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization EN IEC 61010-2-061:2021/A11:2021 |
410. |
EN IEC 61010-2-081:2020 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes |
411. |
EN IEC 61010-2-091:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-091: Particular requirements for cabinet X-ray systems EN IEC 61010-2-091:2021/A11:2021 |
412. |
EN IEC 61010-2-130:2021 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-130: Particular requirements for equipment intended to be used in educational establishments by children |
413. |
EN IEC 61010-2-201:2018 Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-201: Particular requirements for control equipment |
414. |
EN IEC 61010-2-202:2021 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-202: Particular requirements for electrically operated valve actuators |
415. |
EN 61010-031:2015 Safety requirements for electrical equipment for measurement, control and laboratory use – Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test |
416. |
EN 61028:1993 Electrical measuring instruments – X-Y recorders EN 61028:1993/A2:1997 |
417. |
EN 61048:2006 Auxiliaries for lamps – Capacitors for use in tubular fluorescent and other discharge lamp circuits – General and safety requirements EN 61048:2006/A1:2016 |
418. |
EN 61050:1992 Transformers for tubular discharge lamps having a no-load output voltage exceeding 1 kV (generally called neon-transformers) – General and safety requirements EN 61050:1992/A1:1995 |
419. |
EN IEC 61058-1:2018 Switches for appliances – Part 1: General requirements |
420. |
EN 61058-2-1:2011 Switches for appliances – Part 2-1: Particular requirements for cord switches |
421. |
EN 61058-2-4:2005 Switches for appliances – Part 2-4: Particular requirements for independently mounted switches |
422. |
EN 61058-2-5:2011 Switches for appliances – Part 2-5: Particular requirements for change-over selectors |
423. |
EN 61071:2007 Capacitors for power electronics |
424. |
EN 61095:2009 Electromechanical contactors for household and similar purposes |
425. |
EN 61131-2:2007 Programmable controllers – Part 2: Equipment requirements and tests |
426. |
EN 61138:2007 Cables for portable earthing and short-circuiting equipment |
427. |
EN 61140:2002 Protection against electric shock – Common aspects for installation and equipment EN 61140:2002/A1:2006 |
428. |
EN 61143-1:1994 Electrical measuring instruments – X-t recorders – Part 1: Definitions and requirements EN 61143-1:1994/A1:1997 |
429. |
EN 61143-2:1994 Electrical measuring instruments – X-t recorders – Part 2: Recommended additional test methods |
430. |
EN 61184:2017 Bayonet lampholders |
431. |
EN 61187:1994 Electrical and electronic measuring equipment – Documentation EN 61187:1994/AC:1995 |
432. |
EN 61195:1999 Double-capped fluorescent lamps – Safety specifications EN 61195:1999/A1:2013 EN 61195:1999/A2:2015 |
433. |
EN 61199:2011 Single-capped fluorescent lamps – Safety specifications EN 61199:2011/A1:2013 EN 61199:2011/A2:2015 |
434. |
EN 61204:1995 Low-voltage power supply devices, d.c. output – Performance characteristics |
435. |
EN IEC 61204-7:2018 Low-voltage switch mode power supplies – Part 7: Safety requirements |
436. |
EN 61210:2010 Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements |
437. |
EN 61230:2008 Live working – Portable equipment for earthing or earthing and short-circuiting |
438. |
EN 61242:1997 Electrical accessories – Cable reels for household and similar purposes EN 61242:1997/A1:2008 EN 61242:1997/A2:2016 EN 61242:1997/A1:2008/AC:2010 |
439. |
EN 61243-3:2014 Live working – Voltage detectors – Part 3: Two-pole low-voltage type EN 61243-3:2014/AC:2015 EN 61243-3:2014/AC:2015 |
440. |
EN 61270-1:1996 Capacitors for microwave ovens – Part 1: General |
441. |
EN IEC 61293:2020 Marking of electrical equipment with ratings related to electrical supply – Safety requirements |
442. |
EN 61310-1:2008 Safety of machinery – Indication, marking and actuation – Part 1: Requirements for visual, acoustic and tactile signals |
443. |
EN 61310-2:2008 Safety of machinery – Indication, marking and actuation – Part 2: Requirements for marking |
444. |
EN 61310-3:2008 Safety of machinery – Indication, marking and actuation – Part 3: Requirements for the location and operation of actuators |
445. |
EN 61316:1999 Industrial cable reels |
446. |
EN 61347-1:2015 Lamp controlgear – Part 1: General and safety requirements |
447. |
EN 61347-2-2:2012 Lamp controlgear – Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps |
448. |
EN 61347-2-3:2011 Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps EN 61347-2-3:2011/AC:2011 |
449. |
EN 61347-2-7:2012 Lamp controlgear – Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) EN 61347-2-7:2012/A1:2019 EN 61347-2-7:2012/A2:2022 |
450. |
EN 61347-2-8:2001 Lamp controlgear – Part 2-8: Particular requirements for ballasts for fluorescent lamps EN 61347-2-8:2001/A1:2006 EN 61347-2-8:2001/AC:2003 EN 61347-2-8:2001/AC:2010 |
451. |
EN 61347-2-9:2013 Lamp controlgear – Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
452. |
EN 61347-2-10:2001 Lamp controlgear – Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) EN 61347-2-10:2001/A1:2009 EN 61347-2-10:2001/AC:2010 |
453. |
EN 61347-2-11:2001 Lamp controlgear – Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires EN 61347-2-11:2001/AC:2002 EN 61347-2-11:2001/AC:2010 EN 61347-2-11:2001/A1:2019 |
454. |
EN 61347-2-12:2005 Lamp controlgear – Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps) EN 61347-2-12:2005/A1:2010 EN 61347-2-12:2005/AC:2010 |
455. |
EN 61347-2-13:2014 Lamp controlgear – Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules |
456. |
EN IEC 61347-2-14:2018 Lamp controlgear – Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps EN IEC 61347-2-14:2018/A11:2021 |
457. |
EN 61386-1:2008 Conduit systems for cable management – Part 1: General requirements EN 61386-1:2008/A1:2019 |
458. |
EN 61386-21:2004 Conduit systems for cable management – Part 21: Particular requirements – Rigid conduit systems EN 61386-21:2004/A11:2010 EN 61386-21:2004/AC:2004 |
459. |
EN 61386-22:2004 Conduit systems for cable management – Part 22: Particular requirements – Pliable conduit systems EN 61386-22:2004/A11:2010 EN 61386-22:2004/AC:2004 |
460. |
EN 61386-23:2004 Conduit systems for cable management – Part 23: Particular requirements – Flexible conduit systems EN 61386-23:2004/A11:2010 EN 61386-23:2004/AC:2004 |
461. |
EN 61386-24:2010 Conduit systems for cable management – Part 24: Particular requirements – Conduit systems buried underground |
462. |
EN 61386-25:2011 Conduit systems for cable management – Part 25: Particular requirements – Conduit fixing devices |
463. |
EN 61439-1:2011 Low-voltage switchgear and controlgear assemblies – Part 1: General rules |
464. |
EN 61439-2:2011 Low-voltage switchgear and controlgear assemblies – Part 2: Power switchgear and controlgear assemblies |
465. |
EN 61439-3:2012 Low-voltage switchgear and controlgear assemblies – Part 3: Distribution boards intended to be operated by ordinary persons (DBO) EN 61439-3:2012/AC:2019-04 |
466. |
EN 61439-4:2013 Low-voltage switchgear and controlgear assemblies – Part 4: Particular requirements for assemblies for construction sites (ACS) |
467. |
EN 61439-5:2015 Low-voltage switchgear and controlgear assemblies – Part 5: Assemblies for power distribution in public networks EN 61439-5:2015/AC:2015 |
468. |
EN 61439-6:2012 Low-voltage switchgear and controlgear assemblies – Part 6: Busbar trunking systems (busways) |
469. |
EN 61534-1:2011 Powertrack systems – Part 1: General requirements EN 61534-1:2011/A1:2014 EN 61534-1:2011/A11:2021 EN 61534-1:2011/A2:2021 |
470. |
EN 61534-21:2014 Powertrack systems – Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting EN 61534-21:2014/A11:2021 |
471. |
EN 61534-22:2014 Powertrack systems – Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation EN 61534-22:2014/A11:2021 |
472. |
EN IEC 61535:2019 Installation couplers intended for permanent connection in fixed installations |
473. |
EN 61537:2007 Cable management – Cable tray systems and cable ladder systems |
474. |
EN 61549:2003 Miscellaneous lamps EN 61549:2003/A3:2012 EN 61549:2003/A1:2005 EN 61549:2003/A2:2010 |
475. |
EN 61557-1:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 1: General requirements |
476. |
EN 61557-2:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 2: Insulation resistance |
477. |
EN 61557-3:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 3: Loop impedance |
478. |
EN 61557-4:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 4: Resistance of earth connection and equipotential bonding |
479. |
EN 61557-5:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 5: Resistance to earth |
480. |
EN 61557-6:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems |
481. |
EN 61557-7:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 7: Phase sequence |
482. |
EN 61557-8:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 8: Insulation monitoring devices for IT systems |
483. |
EN 61557-9:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 9: Equipment for insulation fault location in IT systems EN 61557-9:2015/AC:2017-02 |
484. |
EN 61557-10:2013 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 10: Combined measuring equipment for testing, measuring or monitoring of protective measures |
485. |
EN 61557-11:2009 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems |
486. |
EN IEC 61557-12:2022 Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC – Equipment for testing, measuring or monitoring of protective measures – Part 12: Power metering and monitoring devices (PMD) |
487. |
EN 61557-13:2011 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems |
488. |
EN 61557-14:2013 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 14: Equipment for testing the safety of electrical equipment of machinery |
489. |
EN 61557-15:2014 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 15: Functional safety requirements for insulation monitoring devices in IT systems and equipment for insulation fault location in IT systems |
490. |
EN 61557-16:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 16: Equipment for testing the effectiveness of the protective measures of electrical equipment and/or medical electrical equipment |
491. |
EN IEC 61558-1:2019 Safety of transformers, reactors, power supply units and combinations thereof – Part 1: General requirements and tests |
492. |
EN 61558-2-1:2007 Safety of power transformers, power supplies, reactors and similar products – Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications |
493. |
EN 61558-2-2:2007 Safety of power transformers, power supplies, reactors and similar products – Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers |
494. |
EN 61558-2-3:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners |
495. |
EN 61558-2-4:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers |
496. |
EN 61558-2-5:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-5: Particular requirements and tests for transformer for shavers, power supply units for shavers and shaver supply units |
497. |
EN 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
498. |
EN 61558-2-7:2007 Safety of power transformers, power supplies, reactors and similar products – Part 2-7: Particular requirements and tests for transformers and power supplies for toys |
499. |
EN 61558-2-8:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes |
500. |
EN 61558-2-9:2011 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps |
501. |
EN 61558-2-12:2011 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage |
502. |
EN 61558-2-13:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers |
503. |
EN 61558-2-14:2013 Safety of transformers, reactors, power supply units and combination thereof – Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers |
504. |
EN 61558-2-15:2012 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations |
505. |
EN 61558-2-16:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units EN 61558-2-16:2009/A1:2013 |
506. |
EN 61558-2-20:2011 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-20: Particular requirements and tests for small reactors |
507. |
EN 61558-2-23:2010 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites |
508. |
EN 61558-2-26:2013 Safety of transformers, reactors, power supply units and combinations thereof – Part 2-26: Particular requirements and tests for transformers and power supply units for saving energy and other purposes |
509. |
EN 61643-11:2012 Low-voltage surge protective devices – Part 11: Surge protective devices connected to low-voltage power systems – Requirements and test methods EN 61643-11:2012/A11:2018 |
510. |
EN 61643-21:2001 Low voltage surge protective devices – Part 21: Surge protective devices connected to telecommunications and signalling networks – Performance requirements and testing methods EN 61643-21:2001/A1:2009 EN 61643-21:2001/A2:2013 |
511. |
EN 61643-31:2019 Low-voltage surge protective devices – Part 31: Requirements and test methods for SPDs for photovoltaic installations |
512. |
EN IEC 61730-1:2018 Photovoltaic (PV) module safety qualification – Part 1: Requirements for construction EN IEC 61730-1:2018/AC:2018-06 |
513. |
EN IEC 61730-2:2018 Photovoltaic (PV) module safety qualification – Part 2: Requirements for testing EN IEC 61730-2:2018/AC:2018-06 |
514. |
EN 61770:2009 Electric appliances connected to the water mains – Avoidance of backsiphonage and failure of hose-sets EN 61770:2009/AC:2011 |
515. |
EN 61800-5-1:2007 Adjustable speed electrical power drive systems – Part 5-1: Safety requirements – Electrical, thermal and energy EN 61800-5-1:2007/A1:2017 EN 61800-5-1:2007/A11:2021 |
516. |
EN 61812-1:2011 Time relays for industrial and residential use – Part 1: Requirements and tests |
517. |
EN IEC 61851-1:2019 Electric vehicle conductive charging system – Part 1: General requirements |
518. |
EN 61851-21:2002 Electric vehicle conductive charging system – Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply |
519. |
EN 61851-23:2014 Electric vehicle conductive charging system – Part 23: DC electric vehicle charging station EN 61851-23:2014/AC:2016-06 |
520. |
EN 61851-24:2014 Electric vehicle conductive charging system – Part 24: Digital communication between a d.c. EV charging station and an electric vehicle for control of d.c. charging EN 61851-24:2014/AC:2015 |
521. |
EN 61869-1:2009 Instrument transformers – Part 1: General requirements |
522. |
EN 61869-2:2012 Instrument transformers – Part 2: Additional requirements for current transformers |
523. |
EN 61869-3:2011 Instrument transformers – Part 3: Additional requirements for inductive voltage transformers |
524. |
EN 61869-4:2014 Instrument transformers – Part 4: Additional requirements for combined transformers EN 61869-4:2014/AC:2014 |
525. |
EN 61869-5:2011 Instrument transformers – Part 5: Additional requirements for capacitor voltage transformers EN 61869-5:2011/AC:2015 |
526. |
EN IEC 61914:2021 Cable cleats for electrical installations |
527. |
EN 61921:2003 Power capacitors – Low-voltage power factor correction banks |
528. |
EN 61995-1:2008 Devices for the connection of luminaires for household and similar purposes – Part 1: General requirements EN 61995-1:2008/A1:2017 EN 61995-1:2008/A11:2021 |
529. |
EN 61995-2:2009 Devices for the connection of luminaires for household and similar purposes – Part 2: Standard sheets for DCL |
530. |
EN 62020:1998 Electrical accessories – Residual current monitors for household and similar uses (RCMs) EN 62020:1998/A1:2005 |
531. |
EN 62026-1:2007 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 1: General rules |
532. |
EN 62026-2:2013 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 2: Actuator sensor interface (AS-i) |
533. |
EN 62026-3:2015 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 3: DeviceNet EN 62026-3:2015/AC:2019-12 |
534. |
EN 62026-7:2013 Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 7: CompoNet |
535. |
EN IEC 62031:2020 LED modules for general lighting – Safety specifications EN IEC 62031:2020/A11:2021 |
536. |
EN 62035:2014 Discharge lamps (excluding fluorescent lamps) – Safety specifications EN 62035:2014/A1:2019 |
537. |
EN IEC 62040-1:2019 Uninterruptible power systems (UPS) – Part 1: Safety requirements EN IEC 62040-1:2019/A11:2021 |
538. |
EN 62080:2009 Sound signalling devices for household and similar purposes |
539. |
EN 62094-1:2003 Indicator light units for household and similar fixed-electrical installations – Part 1: General requirements EN 62094-1:2003/A11:2003 |
540. |
EN 62109-1:2010 Safety of power converters for use in photovoltaic power systems – Part 1: General requirements |
541. |
EN 62109-2:2011 Safety of power converters for use in photovoltaic power systems – Part 2: Particular requirements for inverters |
542. |
EN 62135-1:2015 Resistance welding equipment – Part 1: Safety requirements for design, manufacture and installation EN 62135-1:2015/AC:2016-02 |
543. |
EN 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 1: General requirements |
544. |
EN 62196-2:2012 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories EN 62196-2:2012/A12:2014/AC:2014 EN 62196-2:2012/A12:2014 EN 62196-2:2012/A11:2013 |
545. |
EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers |
546. |
EN 62208:2011 Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements |
547. |
EN 62233:2008 Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure EN 62233:2008/AC:2008 |
548. |
EN 62253:2011 Photovoltaic pumping systems – Design qualification and performance measurements |
549. |
EN IEC 62275:2019 Cable management systems – Cable ties for electrical installations |
550. |
EN 62282-3-100:2012 Fuel cell technologies – Part 3-100: Stationary fuel cell power systems – Safety |
551. |
EN 62282-3-300:2012 Fuel cell technologies – Part 3-300: Stationary fuel cell power systems – Installation |
552. |
EN 62282-5-1:2012 Fuel cell technologies – Part 5-1: Portable fuel cell power systems – Safety |
553. |
EN 62310-1:2005 Static transfer systems (STS) – Part 1: General and safety requirements |
554. |
EN 62311:2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300 GHz) |
555. |
EN 62368-1:2014 Audio/video, information and communication technology equipment – Part 1: Safety requirements (IEC 62368-1:2014, modified) EN 62368-1:2014/AC:2015 |
556. |
EN 62395-1:2013 Electrical resistance trace heating systems for industrial and commercial applications – Part 1: General and testing requirements |
557. |
EN 62423:2012 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses EN 62423:2012/A11:2021 EN 62423:2012/A12:2022 |
558. |
EN 62444:2013 Cable glands for electrical installations |
559. |
EN 62471:2008 Photobiological safety of lamps and lamp systems |
560. |
EN 62477-1:2012 Safety requirements for power electronic converter systems and equipment – Part 1: General EN 62477-1:2012/A11:2014 EN 62477-1:2012/A1:2017 EN 62477-1:2012/A12:2021 |
561. |
EN 62479:2010 Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz) |
562. |
EN 62493:2010 Assessment of lighting equipment related to human exposure to electromagnetic fields |
563. |
EN 62532:2011 Fluorescent induction lamps – Safety specifications |
564. |
EN 62549:2011 Articulated systems and flexible systems for cable guiding |
565. |
EN 62560:2012 Self-ballasted LED-lamps for general lighting services by voltage > 50 V – Safety specifications EN 62560:2012/A1:2015 EN 62560:2012/A1:2015/AC:2015 EN 62560:2012/AC:2015 EN 62560:2012/A11:2019 |
566. |
EN 62606:2013 General requirements for arc fault detection devices EN 62606:2013/A1:2017 |
567. |
EN 62626-1:2014 Low-voltage switchgear and controlgear enclosed equipment – Part 1: Enclosed switch-disconnectors outside the scope of IEC 60947-3 to provide isolation during repair and maintenance work |
568. |
HD 62640:2015 Residual current devices with or without overcurrent protection for socket-outlets for household and similar uses |
569. |
EN 62776:2015 Double-capped LED lamps designed to retrofit linear fluorescent lamps – Safety specifications |
570. |
EN 62868:2015 Organic light emitting diode (OLED) panels for general lighting – Safety requirements |
571. |
EN 62949:2017 Particular safety requirements for equipment to be connected to information and communication networks |
572. |
EN 63024:2018 Requirements for automatic reclosing devices (ARDs) for circuit-breakers, RCBOs and RCCBs for household and similar uses |
573. |
EN IEC 63044-3:2018 Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 3: Electrical safety requirements |
ANNEX II
|
Reference of the standard |
Date of withdrawal |
||||
1. |
EN 60335-2-24:2010 Household and similar electrical appliances – Safety – Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers EN 60335-2-24:2010/A1:2019 EN 60335-2-24:2010/A11:2020 EN 60335-2-24:2010/A2:2019 Restriction: For the purposes of presumption of conformity with the corresponding safety objectives, referred to in Article 3 of Directive 2014/35/EU and set out in Annex I to that Directive:
|
13.6.2025 |
||||
2. |
EN 60335-2-30:2009 Household and similar electrical appliances – Safety – Part 2-30: Particular requirements for room heaters EN 60335-2-30:2009/A11:2012 EN 60335-2-30:2009/AC:2010 EN 60335-2-30:2009/AC:2014 EN 60335-2-30:2009/A1:2020 EN 60335-2-30:2009/A12:2020 |
17.9.2024 |
||||
3. |
EN 60598-2-22:2014 Luminaires – Part 2-22: Particular requirements – Luminaires for emergency lighting EN 60598-2-22:2014/AC:2015 EN 60598-2-22:2014/AC:2016-05 EN 60598-2-22:2014/AC:2016-09 EN 60598-2-22:2014/A1:2020 |
11.7.2024 |
||||
11. |
EN 61347-2-7:2012 Lamp controlgear – Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) EN 61347-2-7:2012/A1:2019 |
11.7.2024 |
||||
12. |
EN 62423:2012 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses EN 62423:2012/A11:2021 |
17.9.2024 |
ANNEX III
No |
Reference of the standard |
Date of withdrawal |
1. |
HD 361 S3:1999 System for cable designation HD 361 S3:1999/A1:2006, HD 361 S3:1999/AC:1999 |
13.6.2025 |
2. |
HD 605 S2:2008 Electric cables – Additional test methods HD 605 S2:2008/AC:2010 |
13.6.2025 |
3. |
EN 50363-0:2011 Insulating, sheathing and covering materials for low-voltage energy cables – Part 0: General introduction |
13.6.2025 |
4. |
EN 50363-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 1: Cross-linked elastomeric insulating compounds |
13.6.2025 |
5. |
EN 50363-2-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 2-1: Cross-linked elastomeric sheathing compounds EN 50363-2-1:2005/A1:2011 |
13.6.2025 |
6. |
EN 50363-2-2:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 2-2: Cross-linked elastomeric covering compounds |
13.6.2025 |
7. |
EN 50363-3:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 3: PVC insulating compounds EN 50363-3:2005/A1:2011 |
13.6.2025 |
8. |
EN 50363-4-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 4-1: PVC sheathing compounds |
13.6.2025 |
9. |
EN 50363-4-2:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 4-2: PVC covering compounds |
13.6.2025 |
10. |
EN 50363-5:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 5: Halogen-free, cross-linked insulating compounds EN 50363-5:2005/A1:2011 |
13.6.2025 |
11. |
EN 50363-6:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 6: Halogen-free, cross-linked sheathing compounds EN 50363-6:2005/A1:2011 |
13.6.2025 |
12. |
EN 50363-7:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 7: Halogen-free, thermoplastic insulating compounds |
13.6.2025 |
13. |
EN 50363-8:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 8: Halogen-free, thermoplastic sheathing compounds EN 50363-8:2005/A1:2011 |
13.6.2025 |
14. |
EN 50363-9-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 9-1: Miscellaneous insulating compounds – Cross-linked polyvinyl chloride (XLPVC) |
13.6.2025 |
15. |
EN 50363-10-1:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 10-1: Miscellaneous sheathing compounds – Cross-linked polyvinyl chloride (XLPVC) |
13.6.2025 |
16. |
EN 50363-10-2:2005 Insulating, sheathing and covering materials for low voltage energy cables – Part 10-2: Miscellaneous sheathing compounds – Thermoplastic polyurethane |
13.6.2025 |
17. |
EN 50395:2005 Electrical test methods for low voltage energy cables EN 50395:2005/A1:2011 |
13.6.2025 |
18. |
EN 50396:2005 Non electrical test methods for low voltage energy cables EN 50396:2005/A1:2011 |
13.6.2025 |
19. |
EN 50497:2007 Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables |
13.6.2025 |
20. |
EN 50565-1:2014 Electric cables – Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) – Part 1: General guidance |
13.6.2025 |
21. |
EN 50565-2:2014 Electric cables – Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) – Part 2: Specific guidance related to EN 50525 cable types |
13.6.2025 |
22. |
EN 60228:2005 Conductors of insulated cables EN 60228:2005/AC:2005 |
13.6.2025 |
23. |
EN 60332-1-1:2004 Tests on electric and optical fibre cables under fire conditions – Part 1-1: Test for vertical flame propagation for a single insulated wire or cable – Apparatus EN 60332-1-1:2004/A1:2015 |
13.6.2025 |
24. |
EN 60332-1-2:2004 Tests on electric and optical fibre cables under fire conditions – Part 1-2: Test for vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixed flame EN 60332-1-2:2004/A1:2015 |
13.6.2025 |
25. |
EN 60332-1-3:2004 Tests on electric and optical fibre cables under fire conditions – Part 1-3: Test for vertical flame propagation for a single insulated wire or cable – Procedure for determination of flaming droplets/particles EN 60332-1-3:2004/A1:2015 |
13.6.2025 |
26. |
EN 60332-2-1:2004 Tests on electric and optical fibre cables under fire conditions – Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus |
13.6.2025 |
27. |
EN 60332-2-2:2004 Tests on electric and optical fibre cables under fire conditions – Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame |
13.6.2025 |
28. |
EN 60332-3-10:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables – Apparatus |
13.6.2025 |
29. |
EN 60332-3-21:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A F/R |
13.6.2025 |
30. |
EN 60332-3-22:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A |
13.6.2025 |
31. |
EN 60332-3-23:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B |
13.6.2025 |
32. |
EN 60332-3-24:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category C |
13.6.2025 |
33. |
EN 60332-3-25:2009 Tests on electric and optical fibre cables under fire conditions – Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category D |
13.6.2025 |
34. |
EN 60335-2-11:2010 Household and similar electrical appliances – Safety – Part 2-11: Particular requirements for tumble dryers EN 60335-2-11:2010/A11:2012 EN 60335-2-11:2010/A1:2015 |
17.9.2024 |
35. |
EN 60598-1:2015 Luminaires – Part 1: General requirements and tests EN 60598-1:2015/AC:2015 EN 60598-1:2015/AC:2016 EN 60598-1:2015/AC:2017-05 EN 60598-1:2015/A1:2018 |
11.7.2024 |
36. |
EN 60598-2-11:2013 Luminaires – Part 2-11: Particular requirements – Aquarium luminaires |
17.9.2024 |
37. |
EN 60754-1:2014 Test on gases evolved during combustion of materials from cables – Part 1: Determination of the halogen acid gas content |
13.6.2025 |
38. |
EN 60754-2:2014 Test on gases evolved during combustion of materials from cables – Part 2: Determination of acidity (by pH measurement) and conductivity |
13.6.2025 |
39. |
EN 60811-100:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 100: General |
13.6.2025 |
40. |
EN 60811-201:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 201: General tests – Measurement of insulation thickness |
13.6.2025 |
41. |
EN 60811-202:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 202: General tests – Measurement of thickness of non-metallic sheath |
13.6.2025 |
42. |
EN 60811-203:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 203: General tests – Measurement of overall dimensions |
13.6.2025 |
43. |
EN 60811-301:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 301: Electrical tests – Measurement of the permittivity at 23 °C of filling compounds |
13.6.2025 |
44. |
EN 60811-302:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 302: Electrical tests – Measurement of the d.c. resistivity at 23 °C and 100 °C of filling compounds |
13.6.2025 |
45. |
EN 60811-401:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven |
13.6.2025 |
46. |
EN 60811-402:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 402: Miscellaneous tests – Water absorption tests |
13.6.2025 |
47. |
EN 60811-403:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 403: Miscellaneous tests – Ozone resistance test on cross-linked compounds |
13.6.2025 |
48. |
EN 60811-404:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths |
13.6.2025 |
49. |
EN 60811-405:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 405: Miscellaneous tests – Thermal stability test for PVC insulations and PVC sheaths |
13.6.2025 |
50. |
EN 60811-406:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 406: Miscellaneous tests – Resistance to stress cracking of polyethylene and polypropylene compounds |
13.6.2025 |
51. |
EN 60811-407:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 407: Miscellaneous tests – Measurement of mass increase of polyethylene and polypropylene compounds |
13.6.2025 |
52. |
EN 60811-408:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 408: Miscellaneous tests – Long-term stability test of polyethylene and polypropylene compounds |
13.6.2025 |
53. |
EN 60811-409:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 409: Miscellaneous tests – Loss of mass test for thermoplastic insulations and sheaths |
13.6.2025 |
54. |
EN 60811-410:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 410: Miscellaneous tests – Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors |
13.6.2025 |
55. |
EN 60811-411:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 411: Miscellaneous tests – Low-temperature brittleness of filling compounds |
13.6.2025 |
56. |
EN 60811-412:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 412: Miscellaneous tests – Thermal ageing methods – Ageing in an air bomb |
13.6.2025 |
57. |
EN 60811-501:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 501: Mechanical tests – Tests for determining the mechanical properties of insulating and sheathing compounds |
13.6.2025 |
58. |
EN 60811-502:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 502: Mechanical tests – Shrinkage test for insulations |
13.6.2025 |
59. |
EN 60811-503:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 503: Mechanical tests – Shrinkage test for sheaths |
13.6.2025 |
60. |
EN 60811-504:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 504: Mechanical tests – Bending tests at low temperature for insulation and sheaths |
13.6.2025 |
61. |
EN 60811-505:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 505: Mechanical tests – Elongation at low temperature for insulations and sheaths |
13.6.2025 |
62. |
EN 60811-506:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 506: Mechanical tests – Impact test at low temperature for insulations and sheaths |
13.6.2025 |
63. |
EN 60811-507:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 507: Mechanical tests – Hot set test for cross-linked materials |
13.6.2025 |
64. |
EN 60811-508:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 508: Mechanical tests – Pressure test at high temperature for insulation and sheaths |
13.6.2025 |
65. |
EN 60811-509:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 509: Mechanical tests – Test for resistance of insulations and sheaths to cracking (heat shock test) |
13.6.2025 |
66. |
EN 60811-510:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 510: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after thermal ageing in air |
13.6.2025 |
67. |
EN 60811-511:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 511: Mechanical tests – Measurement of the melt flow index of polyethylene compounds |
13.6.2025 |
68. |
EN 60811-512:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 512: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature |
13.6.2025 |
69. |
EN 60811-513:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 513: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after conditioning |
13.6.2025 |
70. |
EN 60811-601:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 601: Physical tests – Measurement of the drop point of filling compounds |
13.6.2025 |
71. |
EN 60811-602:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 602: Physical tests – Separation of oil in filling compounds |
13.6.2025 |
72. |
EN 60811-603:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 603: Physical tests – Measurement of total acid number of filling compounds |
13.6.2025 |
73. |
EN 60811-604:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 604: Physical tests – Measurement of absence of corrosive components in filling compounds |
13.6.2025 |
74. |
EN 60811-605:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 605: Physical tests – Measurement of carbon black and/or mineral filler in polyethylene compounds |
13.6.2025 |
75. |
EN 60811-606:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 606: Physical tests – Methods for determining the density#IEC 60811-606:2012 |
13.6.2025 |
76. |
EN 60811-607:2012 Electric and optical fibre cables – Test methods for non-metallic materials – Part 607: Physical tests – Test for the assessment of carbon black dispersion in polyethylene and polypropylene |
13.6.2025 |
77. |
EN 61034-1:2005 Measurement of smoke density of cables burning under defined conditions – Part 1: Test apparatus EN 61034-1:2005/A1:2014 |
13.6.2025 |
78. |
EN 61034-2:2005 Measurement of smoke density of cables burning under defined conditions – Part 2: Test procedure and requirements EN 61034-2:2005/A1:2013 |
13.6.2025 |
79. |
EN 61557-12:2008 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 12: Performance measuring and monitoring devices (PMD) |
11.7.2024 |