COMMISSION REGULATION (EU) 2019/2021
of 1 October 2019
laying down ecodesign requirements for electronic displays pursuant to Directive 2009/125/EC of the European Parliament and of the Council, amending Commission Regulation (EC) No 1275/2008 and repealing Commission Regulation (EC) No 642/2009
(Text with EEA relevance)
Article 1
Subject matter and scope
Article 2
Definitions
Article 3
Ecodesign requirements
Article 4
Conformity assessment
Article 5
Verification procedure for market surveillance purposes
Article 6
Circumvention and software updates
Article 7
Indicative benchmarks
Article 8
Review
Article 9
Amendment to Regulation (EC) No 1275/2008
Article 10
Repeal
Article 11
Entry into force and application
ANNEX I
Definitions applicable for the Annexes
ANNEX II
Ecodesign requirements
A. ENERGY EFFICIENCY REQUIREMENTS
1.
ENERGY EFFICIENCY INDEX LIMITS FOR ON-MODE
|
EEImax for electronic displays with resolution up to 2 138 400 pixels (HD) |
EEImax for electronic displays with resolution above 2 138 400 pixels (HD) and up to 8 294 400 pixels (UHD-4k) |
EEImax for electronic displays with resolution above 8 294 400 pixels (UHD-4k) and for MicroLED displays |
1 March 2021 |
0,90 |
1,10 |
n.a. |
1 March 2023 |
0,75 |
0,90 |
0,90 |
B. ALLOWANCES AND ADJUSTMENTS FOR THE PURPOSE OF THE EEI CALCULATION AND FUNCTIONAL REQUIREMENTS
1.
Electronic displays with automatic brightness control (ABC)
2.
Forced menu and set up menus
3.
Peak white luminance ratio
C. OFF MODE, STANDBY AND NETWORKED STANDBY MODE REQUIREMENTS
1.
Power demand limits other than on-mode
|
Off mode |
Standby mode |
Networked standby mode |
||
Maximum limits |
0,30 |
0,50 |
2,00 |
||
Allowances for additional functions when present and enabled |
|
|
|
||
|
0,0 |
0,20 |
0,20 |
||
|
0,0 |
0,50 |
0,50 |
||
|
0,0 |
1,00 |
1,00 |
||
|
0,0 |
0,0 |
4,00 |
||
Total maximum power demand with all additional functions when present and enabled |
0,30 |
2,20 |
7,70 |
2.
Availability of off, standby and networked standby modes
3.
Automatic standby in televisions
4.
Automatic standby in displays other than televisions
D. MATERIAL EFFICIENCY REQUIREMENTS
1.
Design for dismantling, recycling and recovery
2.
Marking of plastic components
3.
Cadmium logo
Cadmium inside |
Cadmium free |
[Bild bitte in Originalquelle ansehen] |
[Bild bitte in Originalquelle ansehen] |
4.
Halogenated flame retardants
5.
Design for repair and reuse
E. INFORMATION AVAILABILITY REQUIREMENTS
1.
Availability of software and firmware updates
ANNEX III
Measurement methods and calculations
1.
General conditions
2.
Measurements of on mode power demand
Measurements of peak white luminance
ANNEX IV
Verification procedure for market surveillance purposes
1.
General procedure
1.1.
Verification procedure for requirements established in Annex II, point B.1
1.2.
Verification procedure for requirements established in Annex II, point B.2
1.3.
Verification procedure for requirements established in Annex II, point B.3
1.4.
Verification procedure for requirements established in Annex II, point C.1
1.5.
Verification procedure for requirements established in Annex II, point C.2
1.6.
Verification procedure for requirements established in Annex II, point C.3
1.7.
Verification procedure for requirements established in Annex II, point C.4
1.8.
Verification procedure for requirements established in Annex II, point D and E
2.
Procedure if requirements are not achieved
3.
Verification tolerances
Parameter |
Verification tolerances |
On mode power demand, (Pmeasured , Watts) excluding allowances and adjustments in Annex II, point B, for the purposes of EEI calculation set out in Annex II, point A. |
The determined value (*1) shall not exceed the declared value by more than 7 % |
Off mode, standby mode and networked standby mode power demand (Watts), as applicable |
The determined value (*1) shall not exceed the declared value by more than 0,10 Watt if the declared value is 1,00 W or less, or by more than 10 % if the declared value is more than 1,00 W |
Peak white luminance ratio |
Where applicable, the determined value shall not be lower than 60 % of the peak white luminance of the brightest on mode configuration provided by the electronic display |
Peak white luminance (cd/m2) |
The determined value (*1) shall not be lower than the declared value by more than 8 % |
Visible screen diagonal in centimetres (and inches, if declared) |
The determined value (*1) shall not be lower than the declared value by more than 1 cm (or 0,4 inches). |
Screen area in dm2 |
The determined value (*1) shall not be lower than the declared value by more than 0,1 dm2 |
Timed functions as set out in Annex II, points C.3 and C.4 |
The switch shall be completed within 5 seconds of the set out values |
Weight of plastic components as qualified in Annex II, point D.2 |
The determined value (*1) shall not be different from the declared value by more than 5 grams |
ANNEX V
Benchmarks
Diagonal of screen area |
HD |
UHD |
|
(cm) |
(inches) |
Watt |
Watt |
55,9 |
22 |
15 |
|
81,3 |
32 |
25 |
|
108,0 |
43 |
33 |
47 |
123,2 |
49 |
43 |
57 |
152,4 |
60 |
62 |
67 |
165,1 |
65 |
56 |
71 |
Other functioning modes: |
|||
Off mode (physical switch): |
0,0 W |
||
Off mode (no physical switch): |
0,1 W |
||
Standby |
0,2 W |
||
Networked standby (non-HiNA): |
0,9 W |